no it is not an interference engine
The horse power is 175
Yes, the size 38W x 34L and XL are considered a size. 38W is the waistline and 34L is the length. XL stands for extra large.
Actually, I had a 97 Beretta engine put into my 95 Lumina and it was fine.
the plug gap is 0.60. hope this helps...
clean iac sensor and o ring
195 fp n 205 for gt
That's the waist and the inside leg measurement in inches.
it is located right underneath the throttle body just look down there and youll see it :)
take it to a Toyota dealership, have them run the code through the scan tool and reset the light as necessaryAnswerYou could, if you want to waste your money. All you have to do is disconnect the negative cable from your battery, wait a minute and reconnect it. This resets your computer. Also, you can buy a cheap code reader for around $50 instead of paying around $80 to get it done at the dealership. They are easy to use and plug in usually under your steering wheel or under the seat. They are useful for finding whats wrong but wont tell you great details like the expensive ones do.
You could do as the last guy suggested, which would be a good idea...BUT...in the case that you pull all these plugs out at on time, here are a few good ways to know what firing order they go in: 1. You can go off of the length of the wires. The wires only reach so far and non of them should be over stretched or dangling. 2. The cylinder's order is   <---back of engine     <---front of engine 3. Cylinder 1 ignition coil is ALWAYS connected to number 4 Cylinder 3 ignition coil is ALWAYS connected to number 6 Cylinder 5 ignition coil is ALWAYS connected to number 2 This is a funky order set up, but that is how it is on the 3.4L V6 engine of my 96 Toyota T100. Hopefully that helps.
For the computer, it is located... Well follow your throtle cable down to the top of you engine. Just below where it attaches, you'll see a two wire plug. Remove the plug, and...there it is. Use a 3/4 in. socket. Now, if we are talking the one for the gauge.... I'll have to let you know. That's what I am here looking for. Adam Shump email@example.com
Use a code scanner to check the engine diagnostic codes. If you see any problems fix that first. If there are no issues, check fuel pressure at the fuel rail test port. If the fuel pressure is low either at an idle or when driving under full power, check and/or replace the fuel filter.
Answer: 68 L NO22NO + O2 ------> 2NO2>68 L + 34 L --> 68 L + some 'left over' NO
15 fp then 75 degrees This is why this site is really lame, this guy/gal is dangerous. the correct value is 44ft/lbs then 90 degree turn +- 5 degrees
Denver International's 16R - 34L is 16000 X 200 feet. That is longer than Kennedy's Space Center which is 15000 feet. Although I'm not sure it it is in fact the longest paved runway in the U.S.
The location for the O2 sensor(s) are on the exhaust manifold in front(before catalyst, catalytic converter) for checking emissions from combustion chamber or behind (after catalyst) for analyzing emissions from the catalytic converter.
Kishore Karke.RankNameNet Worth ($mil)AgeRevenue Source.34L. Madhusudan Rao167043Lanco Group.47G.V. Krishna Reddy107072 GVK Industries Ltd.59Murali Divi91058 Divis Laboratories.88P.V. Ramaprasad Reddy54050 Aurobindo Pharma
The ignition module cannot be tested with an ohm meter. Todays cars are more complicated than the 80's car which can be tested with an ohm meter. It can only be test with a tech 1 scan tool, which are very expensive
You can still get the OEM parts from most Yamaha dealers! They will probably have to order most parts. Or you can look online. there are many sites that sell the OEM parts. I own a 1984 XT600 and I've had no problems finding parts. I hope this helps you!
my girlfriends car is doing the same. it is known ot be the crankshaft sensor. your have two of them one behind the balancer and one under the exhuast manafold on the oxygen sensor side. most likely its the one under the balancer. sometimes its bolth
Ther is usually a temp switch on your radiator that controls the fan. it is normally open when cool and closed at 220. if you want to test your fan you can pull the wires from the switch and put a wire acros the leads this powers the fan to on. if the fan powers on replace the faulty switch.
DARKSEID007 My Advice: The best thing to do is to tighten the sparkplugs down with a ratchet and socket till it is just tight enough to not turn by your fingers. (SNUG if you will technical terms) then you take the ratchet and turn it 1/4 of a turn and it will tighten it enough without overtightening or stripping the threads out of the motor. 1/4 means if u have the ratchet end at a 12 o' clock position turn it till the end of the ratchet goes around to the 3 o' clock position. Hope this helps.
The south end of Runway-34L at Narita International Airport is located at 35.7492Â° north latitude 140.3864Â° east longitude. In the city, the center of the penthouse-level rooftop on the Tokyo Palace Hotel, just southeast of the Imperial Palace grounds, is located at 35.6846Â° north latitude 139.7614Â° east longitude. Other places around the city and the prefecture have different coordinates.
Verify the plug wires are connected correctly. Look here: http://autorepair.about.com/library/firing_orders/bl-fo-1312.htm It can also be a bad spark plug, or plug wire. A burnt valve or blown head gasket is another possibility. A weak injector on that cylinder is possible. A compression check is in order if the ignition system is found to be OK. This will detect a blown gasket or burnt valve.