answersLogoWhite

0


Best Answer

try getting your CV Joint replaced.

User Avatar

Wiki User

โˆ™ 2006-03-26 12:58:21
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: 2001 Chevy Impala clunk sound from right of car when turning only when car is in motion both at high and low speeds I had the struts mounts and bearings replaced and still problem persists?
Write your answer...
Submit
Related questions

Why does your 1991 Chevy Cavalier make a buzzing sound from the front left when driving straight or turning left but not when turning right?

This buzzing indicates that the wheel bearings need to be replaced on your front left wheel. This can be fixed by changing the bearings themselves or replacing the entire wheel hub.


Why does power steering work turning to left but not right already replaced pump no difference?

The problem is your rack and pinion .


Grinding noise when turning right only when starting from a full stop No sounds turning while driving Changed both wheel bearings checked CV joints problem still there?

broken motor mount(s)


Why fan stop turning on the goodman ck30-1b air conditioner?

Goodman CK30-1B : Just had the same problem. dual run capacitor burned out, whcih was caused by fan motor overheating (bearings worn out) or vice versa, which burned out yet another capacitor, until I replaced the fan motor.


What makes a clunking noise when turning?

Wheel bearings or u joints


Have 02 Saturn SL 2 26000 mi grinding noise when turning right or left has new brakes tie rods steering rack all dealer replaced this week still makes grinding sound when turning right left?

Bad wheel bearings usually cause a grinding noise, and are known to only cause it when turning.


I have had the wheel bearings power steering pump tensioner and a bunch of other things replaced on my 1999 Pontiac Sunfire and it still squeals What could be the problem Also had a few pully's?

Can you tell us little more? Does the engine squeal when the car is just sitting and idling? Or, is the squeal from the suspension .... it squeals when you're moving or turning?


1994 buick lesabre. noise from wheel when turning wheels left or right hits the limits?

Check your wheel bearings. Mine made a noise when turning right and had to replace the wheel bearings and hubs as they are all one unit on my 92.


What could be noise coming from under the car that sounds like stuck paper in spokes turning while the car is accelerating?

This buzzing noise is likely a faulty wheel bearing. The bearings are moving around randomly and need to be replaced.


Why does 2005 Toyota sienna squeal when initially turning ac on?

The AC belts are probably stretched and loose. I had the same problem and replaced belts and cured squeak.


Why did The right two gauges stoped working and the power to the ac go out on my 2000 Malibu?

I have a 2000 Malibu and I am having the same problem. There is an electrical problem. I have yet to figure out how to solve it, but turning on the AC blows the fuse. Ive had the instrument cluster replaced, so dont go and do that, because your car will still do the same thing. Your BCM (Body Control Module) may need to be replaced, or it is just a bad wiring. If you have replaced your battery, that may be a part of the problem. I know this information is not much, but hopefully it will help. I have a 2000 Malibu and I am having the same problem. There is an electrical problem. I have yet to figure out how to solve it, but turning on the AC blows the fuse. Ive had the instrument cluster replaced, so dont go and do that, because your car will still do the same thing. Your BCM (Body Control Module) may need to be replaced, or it is just a bad wiring. If you have replaced your battery, that may be a part of the problem. I know this information is not much, but hopefully it will help.


1998 Honda CR-V knocking from the rear when turning?

This is a common problem. just get the rear differential fluid replaced. it will fix it. Dealer charges around $80 for that.


If you are overheating and have coolant what are the chances its your thermostat?

I had this problem on my 2001 GC....had it fixed several months ago....there was a recall on certain yrs of the WJ style grand cherokee, due to bad fan bearings. Your cooling fan will sound like it kicks on when it should, because the motor does activate however the fan is not turning due to the shot bearings. Contact your local dealer, should be a free fan replacement if that is the problem.


Problem with turning the ignition in your jeep when starting the car how do you fix it?

Physically has a turning problem ? Try your spare key and still has the problem? Replace the ignition switch.


Why does a 1995 Cadillac Concourse have a popping noise in the front end when making turns to left or right?

The Cv joint in the front axle has worn out and needs to be replaced. Most of the time it is cheaper to replace the whole axle than to rebuild just the joint itself. I would suggest that you investigate the bearing(s) at the top of the strut tower. If the popping occurs when you turn the steering wheel, then it is this bearing not the CV joint... the CV joint will make noise as the front wheels are turning. Your question seems to indicate the problem when turning the steering wheel. It could be one or both of the bearings on either side. Judging by the year, this could be the problem. It requires dropping the strut and replacement of the bearing then a wheel alignment for either one or both bearings.


97 Chevy silverado Truck makes a popping noise turning right while braking and turning?

you might want to check your left side wheel bearings


What would cause a knocking or clunking noise from rear tires when turning?

You probably need your bearings repacked


What is pinion pre load?

It is the compression put on the bearings during assembly. It is measured as a turning torque measurement.


Why does your 2003 s-10 zr2 rear axle bind up when turning around a corner ..could it be because it is on dry pavment be the problem if so is this normal.vehickle in 4-wheel drive.?

You may have bad wheel bearings. Check them out.


Why is my Car making grinding noise?

AnswerThere are a couple of things... If it happens when you are turning and the sound gets louder then it is your CV Joint that needs to be replaced. If the grinding noise is only when you break then it is your break pads and they need to be replaced. If it is just when you drive and is pretty loud then it is your wheel bearings. Don't get bent out of shape if you replace one wheel bearing and the noise is there... it just means you probably should replace all the wheel bearings (better anyways).


Why is a 2002 Hyundai Elantra making a vibration sound that gets loudest at around 35-40 mph gets much louder when turning to the left and quieter when turning to the right?

sounds to me that the right from bearing hub needs to be replaced. Had the same problem on a 97 Hyundia


What would cause a grinding noise from the rear-end of a 1997 Toyota Rav4 all wheel drive the noise happens mostly when turning corners is it the rear diff or hub bearings?

If it happens only when turning corners, this is likely to come from the differential. A ball bearing problem would make noise all the time.


Is it your ball bearing when the car makes a humming noise when turning the wheel to the right or left?

could be your wheel bearings


How do you get the head light capsules out of a 1996 Monte Carlo?

headlight must be replaced as an assembly bulb can be replaced by turning and pulling


Do your wheel bearings need replaced?

Yes! These pin bearings are surrounded by high temp grease, the grease is kept where it should be by rubber seals. Once these seals are worn out, and cracked, or broken completely, the grease finds its way away from the bearings, and then you have metal on metal contact. There are four parts to a bearing system on each wheel; the inner bearing, outter bearing, and racers for both. the bearings run along the racers, and without the proper amount, and quality grease, these pin bearings with soon break the racer/lose bearing from retainer/lock up/or just simply over heat and STOP the wheel from turning. so, replace those bearings, and get NEW high temp bearing grease and chock it FULL. this will prevent any future problems.