answersLogoWhite

0


Best Answer

Check the throttle position sensor or the idle control motor

User Avatar

Wiki User

โˆ™ 2006-09-27 01:43:58
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: 97 Chevy venture wont start unless gas pedal is pressed and held a 2k idle?
Write your answer...
Submit
Related questions

What is a clutch safety switch?

It prevents engine cranking unless the clutch pedal is pressed.


How do you fix a gas pedal on a 1986 Chevy pickup which the wire is not fitted to the gas pedal Pressed down on it then it came loose?

get a new one


How do you use pedal in a sentence?

She pressed on the gas pedal to make the car go forward.He pressed on the sustain pedal while he played piano.


Which pedal in a car is pressed when changing gears?

the clutch pedal


What causes Turn signals light up when brake pedal pushed on 2001 venture?

common problem on the Chevy venture, there is a bad circuit board inside the tail light lens on each side. the bulbs plug into it and it costs about $35 each to replace, unless you want oem, then around $120 each.


Can you make a sentence using pedal?

I pressed the pedal to move faster in my car.


When a piano has a third pedal what does that extra middle pedal do?

It's called a Sostenato pedal and it sustains only the notes that are being held down when the pedal is pressed.


Noises when you push gas pedal?

ticking noise when the gas pedal is pressed in a 2005 ford ranger


What will cause a Chevy 350 V8 engine to cut off when the accelerator is pressed?

if it runs fine until you push the gas pedal the accelerator pump may be bad if it has a carb on it.


Where does the clutch located on the 88 Chevy Caprice?

The clutch pedal is the one left of the brake pedal. The clutch disk the pedal affects is inside the transmission bell housing where the engine block bolts to the transmission. Unless you have an automatic, then your car has no clutch.


1996 Audi a4 do you need to press clutch pedal to start the car?

Yes. unless you bypass the safety device that prevents your car from starting if you dont have the clutch pressed.


Why does my clutch pedal on my 1997 Chevy S-10 go all the way to the floor when pressed Does it need adjustment If so how do I do that?

There is no adjustment on this clutch. The clutch is hydrolic, you may need to bleed it.


What could cause the brakes and brake pedal to stick when brake pedal is pressed?

Check around brake pedal for something rubbing. If OK, I'd look into the master cylinder.


Chevy Venture brake line leaking?

When a brake line is leaking on the Chevy Venture the brake line should be replaced as soon as possible. A leak, however small, can cause hydraulic fluid to escape the brake line which will cause a loss in brake pressure. The brakes should be bled of air after the new line is put in to remove gaps in brake pedal pressure.


What does it mean if truck starts to shake when gas pedal is pressed?

One reason that your truck might start to shake when the gas pedal is pressed is because the tires could need to be balanced. The problem could also be your shock absorbers, or struts. * It has less to do with the gas pedal as it has to do with parts affected by acceleration.


Why does my 1980 Chevy gas pedal get stuck?

If the gas pedal is sticking on a 1980 Chevy, it is possible that the cable is wearing out. Check for slack in the cable. There could also be dirt on the pedal itself that is causing it to stick.


How do you reset the change engine oil light on a 2003 Chevy venture?

turn the key to the on position engine not running step on gas pedal to the floor three times and wait for light to flash and go out and its reset


How do you get the oil life back to 100 percent on a 2004 Chevy Avalanche?

turn the key forward and pump the gas pedal three times and keep it pressed on the 3rd time until it changes back to zero %


Why does my Car wont stay on unless the gas pedal is pressed?

It could be a lot of different things. I would check the idle speed unless it's computer controlled. If the idle speed is computer controlled you can't adjust it and it probably isn't the problem anyway.


Where is the best place to tie in the brake switch wire from the electric brake controller on the brake switch on a 96 Chevy 1500 silverado?

The wire you are looking for is a white wire in the bundle that is closest to the brake pedal. Use a test light or meter to check voltage going through the wire when the pedal is pressed.


Does the Mercedes 2003 and above consume gas if it's running and i am not pressing the gas pedal?

If the engine is running it is burning fuel, whether the gas pedal is pressed or not.


Why don't my hazard lights flash when the brake pedal is pressed on your 1997 Chevy s-10?

This is normal. The 4-way and brake light share the same bulb. The brake light overrides the 4-way when applied.


How does the pedal brake work?

The brake pedal itself swings on a pivot when pressed, pushing a piston through the fire wall into the master cylinder. Forcing brake fluid through the brake lines into a proportioning valve, then into the brakes themselves, bringing the vehicle to a stop. As soon as the brake pedal is pressed, it activates a switch that turns the brake lights on.


Where is the brake light pedal switch on a 2004 Chevy Malibu?

the switch is on top back side of brake pedal.


Brake light switch sticks 0n 1994 Chevy blazer keeps brake lights on until you move brake pedal?

Brake Lights Stay on Unless the Brake Pedal is RaisedThis is usually caused by the brake light switch being out of adjustment in its physical distance to the contact point on the brake pedal arm.