answersLogoWhite

0


Best Answer

Where is the plenum bolt for a 1994 Toyota pick-up

User Avatar

Wiki User

โˆ™ 2013-10-18 02:54:47
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: A Diagram of a 1990 Toyota Pickup heater plenum?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where is the pcv valve located on a 1992 Toyota Pickup 6-cylinder?

Under the intake plenum


Where is the heater plenum in a 1999 ford explorer?

Heater plenum is the same as the heater box and it spans the width of the passenger side dash behind the glove box. Check heatertreater.net for pictures.


Where is heater core located on a 1987 Chevy Celebrity?

The heater core in a 1987 Chevy Celebrity is in the heater plenum to the right of the hump and below the glove compartment.


Do you have to pull dash to replace heater core on a 1987 grand marquis?

The good folks at Chilton say no you remove the plenum from under the dash and then remove the heater core from the plenum. You may want to get the book for this one as they're are about twenty steps (many things to remove) before the plenum will come out. Good luck.


Where is the blower motor on a 86 Chevy Celebrity?

The heater blower motor is under the hood bolted to the heater plenum on the passenger side of the car.


Where is 2001 Cadillac Catera heater control valve?

Behind the intake plenum on the passenger side.


How do you replace rear plugs 2000 Toyota Camry?

remove upper intake plenum


How do I find the heater core on 2001 Ford F-150 xlt?

The heater core is located in the dash ,or should I say in the heater /ac plenum if you chase out the heater hoses from under the hood you'll get a general idea where it is located.


Free diagram heater core replacment 98town car?

1998 Lincoln Town Car Heater Core Heater Air Plenum Chamber Heater Air Plenum Chamber and Air Inlet Duct Removal 1. Disconnect battery ground cable. 2. Disconnect the heater water hoses from the heater core tubes. Plug the ends of the heater water hoses to prevent coolant loss. 3. Plug heater core tubes securely to prevent coolant leakage from heater core during heater air plenum chamber removal. 4. Remove three nuts located below the windshield wiper motor (17508) retaining the LH end of the heater air plenum chamber to the dash panel. 5. Remove one nut retaining the upper LH corner of the A/C evaporator core housing to the dash panel. 6. Remove LH and RH lower instrument panel insulators. 7. Disconnect two vacuum supply hoses from vacuum source. Push grommet and vacuum supply hose into passenger compartment. 8. Remove all instrument panel retaining screws and pull the instrument panel back as far as possible without disconnecting any wire harnesses. 9. Loosen the RH door sill plate and remove the RH side cowl trim panel. 10. Remove cross body brace and disconnect wiring harness from A/C electronic door actuator motor (19E616) and disconnect the sensor tube from the evaporator case connector. 11. Disconnect the vacuum jumper harness at the multiple vacuum connector near the heater outlet floor duct. 12. Disconnect the white vacuum hose from the heater and A/C air inlet duct door vacuum control motor. 13. Remove two hush panels. 14. Remove one plastic push fastener retaining the heater outlet floor duct to the LH end of the heater air plenum chamber. Remove LH screw and loosen RH screw on the rear face of the heater air plenum chamber and remove the heater outlet floor duct. 15. Remove two nuts from the two studs along the lower flange of the heater air plenum chamber. 16. Carefully move heater air plenum chamber rearward to allow heater core tubes and the stud at the top of the heater air plenum chamber to clear holes in the dash panel. Remove heater air plenum chamber from vehicle by rotating the top of the heater air plenum chamber forward, down and out from under the instrument panel. Carefully pull lower edge of instrument panel rearward as necessary while rolling the heater air plenum chamber from behind the instrument panel. Installation 1. Route the vacuum supply hose through the dash panel and seat the grommet in the opening. 2. Position the heater air plenum chamber under the instrument panel with the A/C register duct opening up and the heater core tubes down. Rotate the heater air plenum chamber up behind the instrument panel and position the heater air plenum chamber to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the A/C evaporator core housing. 3. Install three nuts on the studs along the lower flange and one on the upper flange of the heater air plenum chamber. 4. Install three nuts below the windshield wiper motor to attach the LH end of the heater air plenum chamber to the dash panel. 5. Install one nut to retain the upper LH corner of the A/C evaporator core housing to the dash panel. 6. Position heater outlet floor duct on heater air plenum chamber. Install two screws and plastic push fastener. 7. If removed, position heater air damper door vacuum control motor to the mounting bracket. Install two retaining screws. 8. Connect the white vacuum hose to the heater and A/C air inlet duct door vacuum control motor. 9. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the heater outlet floor duct. Install heater outlet floor duct. 10. Connect the sensor tube to the evaporator case connector on EATC-equipped vehicles. 11. Install the cross body brace and connect wiring harness to the A/C electronic door actuator motor. 12. Install the bolt to attach the lower RH end of the instrument panel to the side cowl. 13. Install the RH side cowl trim panel and tighten the RH door sill plate retaining screws. 14. Install glove compartment door (06024) and check arms. 15. Connect vacuum supply hose to vacuum supply. 16. Install RH and LH lower instrument panel insulators. 17. Install two hush panels. 18. Unplug the heater core tubes and connect the heater water hoses to the heater core tubes. 19. Fill the cooling system with coolant to replace coolant lost during removal of the heater air plenum chamber. 20. Connect the battery ground cable. Check the system for proper operation. Removal 1. Remove the heater air plenum chamber assembly as outlined. 2. Remove the four retaining screws from the heater core cover (18B300) and remove the heater core cover from the heater air plenum chamber assembly. 3. Pull the heater core assembly from the heater air plenum chamber assembly. Heater Core Removal Installation 1. Carefully install heater air plenum chamber assembly into the heater air plenum chamber assembly. Visually check to ensure that core seal is properly positioned. 2. Position the heater core cover and install the four retaining screws. 3. Install the heater air plenum chamber assembly as outlined. Heater Core Removal


Where is the plenum box on a 1996 Dodge pickup?

The large plastic box on top with the air filter in it could be called a plenum.The large plastic box on top with the air filter in it could be called a plenum.


How to change heater hose 96 Isuzu Rodeo?

Changing the heater hose hidden between the engine and the firewall under the plenum on a 96 isuzu rodeo. Best option since there is limited access is to remove the plenum. Take all the bolts out of plenum. Remove wire harness to free plenum up enough to remove. Detach from air intake. Then you'll be able to get at that hose. When putting it back on you'll need a new plenum gasket. Hose cost around $10 and gasket is like $6. Garage will probably charge you $300+


Where is the heater resister located on a 1996 ford aerostar?

resister is located on the plenum next to the blower motor under the hood

People also asked