0
A reversed polarity is when the hot and neutral are wired backwards?
Wiki User
∙ 15y ago
Yes in AC circuits the terminology reversed polarity means the hot and neutral are reversed to what they should be. In DC circuits reversed polarity means that the positive and negative terminals are reversed to what they should be.
Wiki User
∙ 15y ago
Wiki User
∙ 14y agoI know the answer, but I'm not taking this test, you are! Study your book and learn the answer yourself. Believe me, I'm doing you a favor.
Add your answer:
Earn +20 pts
What would cause an electric motor to run backwards?
Motors running backwards: A DC motor wired backwards or magnetic field reversed. A 3 phase AC motor with 2 phases reversed A single phase motor will run either way unless it is 'persuaded' by means of a shaded pole or other method to rotate in a particular direction.
What is the use of polarity test?
I will assume that your question is in reference to CT and transformer polarity.In the case of a CT (Current Transformer) they have to be installed in the correct direction for proper metering. The polarity check is used to verify that they are installed correctly and that the polarity marks are correct (if the CT has them).In the case of a transformer there are two types of polarity, additive and subtractive. If you are paralleling transformers you have to ensure that they are the same type polarity in addition to other attributes.Hope this helps.Alternative AnswerIn a new electrical installation, a polarity test is conducted to ensure that socket outlet terminals are correctly wired (line really is line, neutral really is neutral, and the protective conductor (earth/ground) really is protective conductor. It's also important, for example, that the centre pin on an Edison Screw lampholder is connected to line, and not to neutral.
Is polarity important with fluorescent under cabinet lights?
Yes, polarity is always important. Many under cabinet fluorescent fixtures are small enough to use a small transformer rather than a ballast. But even then, the transformer will have a longer life if it's wired with correct polarity.
Does the neutral wire have a charge in a gfci circuit breaker?
No. Not if the GFCI is wired correctly. The neutral wire should always be cold, or at ground potential.
Why rotor of a dc motor moves in the anticlockwise direction?
Positive and negative are reversed. It will run either direction depending on which way it is wired.
How do you wire for reversed polarity?
the hot and neutral are wired forwards the ground and neutral are wired backwards
What causes reversed polarity in a 110 volt receptacles?
Improperly wired receptacle is the normal cause.
When the hot and neutral are wired backward is reversed polarity?
The assumption here is that you're refering to a standard A/C (alternating current) circuit such as those found in the average household or business. In a typical household the power supplied by the power company actually reverses polarity 60 times a second (60 Hz), hence the term alternating current (A/C). In Europe the standard frequency or Hertz (Hz) is 50 at 220 volts. The U.S. standard is, of course, 110 VAC at 60 Hz. So, in answer to your question In most systems you have a 0 volt potential *neutral and a 110 or 220 volt potential *hot, when this gets wired in reverse safety problems can arise, such as a nasty shock when touching grounded equipment.
Is Reverse polarity is when the ground and neutral are wired backwards?
If you are talking about an AC (alternating current) circuit, such as the house mains supply, "reverse polarity" usually means the "hot" and "neutral" wires from the supply have been connected to something the opposite way round to what they should be. If you are talking about a DC (direct current) circuit supplied by a battery, such as in a car, "reverse polarity" usually means the positive and negative leads from the battery have been connected to something the opposite way round to what they should be.
Differentiate between normal and reverse polarity?
It depends on the context. In a.c. circuits, 'reverse polarity' describes a situation in which a device, such as a socket outlet, is wrongly wired -with the line and neutral conductors interchanged.
What is reverse polarity-?
Reverse polarity is the opposite of normal polarity. Normal polarity in electronics is when you have the positive hooked up to the positive terminal and the negative to the negative terminal. Reverse polarity would be having the positive hooked up to the negative terminal and the negative to the positive terminal. The same concept can be used with magnets.
What could you do to troubleshoot a circuit with several hot-neutral reversed outlets if they all appear to be wired correctly ie black-hot to brass and white-neutral to silver?
On polarized receptacles the short slot is the hot side and the taller slot is neutral side. Colors can be swapped around sometimes. If they all are reversed, it is because the line is reversed somewhere, and all of the following outlets "downstream" from that one are reversed. Could even be in the main panel, if everything on the circuit is reversed.
What would cause an electric motor to run backwards?
Motors running backwards: A DC motor wired backwards or magnetic field reversed. A 3 phase AC motor with 2 phases reversed A single phase motor will run either way unless it is 'persuaded' by means of a shaded pole or other method to rotate in a particular direction.
What is importance of a polarity test?
HERE'S AN EXAMPLE: IF THE POLARITY IS BACKWARDS AT A LIGHT FIXTURE THEN THE HOT (120VOLTS) WILL BE THE OUTSIDE OF THE LIGHT BULB SCREW SHELL AND THE MIDDLE PRONG INSIDE THE SOCKET WILL BE THE NEUTRAL -- THEREFORE WHEN YOU CHANGE THE BURNT OUT LIGHT BULB YOU WILL GET SHOCKED BECAUSE THE SCREW SHELL PART IS HOT!! IF WIRED CORRECTLY YOU WILL NOT GET SHOCKED BECAUSE THE HOT (120VOLTS) WILL BE INSIDE THE SCREW SHELL ON THE PRONG AND YOU WON'T BE TOUCHING THAT PART WHEN YOU CHANGE THE LIGHT BULB!!
What happens if you wired your circuit backwards?
Everything will flow backwards
Neutral and hot wired backwards?
For a US 3-prong plug, a smaller slot should be hot, the longer slot should be neutral, and the screw that holds the plate on should be ground. Cheap, inexpensive testers are available at hardware stores.
What is symptom of a circuit incorrectly wired?
Circuit breaker tripping, or non functioning outlet. The neutral and hot can be reversed, or an open ground, and you will have no symptoms. This can only be detected with a circuit tester you plug in to check the wiring.
