0
What is a circuit board that controls all work done by the computer?
Wiki User
∙ 6y ago
The small circuit board that controlls the work done by the computer is a DOCUMENT.
Wiki User
∙ 14y ago
Anonymous
Operating system
Add your answer:
Earn +20 pts
What should be done immediately be done after you assess the hazards to determine the risk?
Implement controls
What can be done to fix a pantech breakout when it wont charge or turn on?
It depends on what caused the device to not power on. The battery could be damaged. Replace the battery. The charging unit could be damaged. Replace the charging unit or find the damaged component and replace it. The charging connector could be damaged. Replace the circuit board or find the damaged component and replace it. The power button could be damaged. Replace the circuit board or find the damaged component and replace it. Something could have fried the circuit board. Replace the circuit board or find the damaged component and replace it.
how do i go about recertifying my CNA in brooklyn?
CALL THE STATE NURSING BOARD AND ASK THEM, OR PULL IT UP ON THE COMPUTER. THAT IS HOW ITS DONE IN FLORIDA AND ARIZONA
How do you replace the wiper motor circuit board?
This is really an easy fix. The wiper motor assembly is on the firewall, just right of center. The wiring can be unplugged before the circuit board is removed, or afterward. I found it easier to unplug it after the circuit board was removed. There is a flat cover that is held on with three torx screws (T20). Remove those screws and remove the cover. The circuit board will now be visible. Remove the circuit board by grasping the wiring connecter and gently pulling it towards the front of the vehicle. When the circuit board has fallen free, unplug it from the wiring harness if you haven't already done so. The solder joints that connect the wiring socket to the board were bad on my board. I just resoldered those and re-installed the circuit board. I did get an entire wiper motor assembly, which included the board, from a salvage yard for $40. I didn't even use it. Excellent answer! My wipers would not start without getting out and helping, then they might or might not continue running after a few wipes. When switched on and not running, module would produce buzzing sound. Followed directions above, and even though the three pins joining the wiring harness plug to the circuit board looked properly soldered, carefully re-soldered making sure to have good solder contact to printed circuit strips. In my case this worked like a charm, and judging from the number of postings for this fix, it seems to be a common problem with this board. It would seem to be a good first step unless there are other obvious signs of failure.
What if you think your parent has put norton parental control on your laptop how do you check or get rid of it?
If your parent has put parental controls on your computer, they have done it for your safety. You don't get rid of them.
What is a processor card and what does it do?
At the heart of every computer is one or more processors. While some hand held devices like mobile phones have the processor fixed to the main circuit board there are computers that allow you to change the number and speed of the processors in the computer. This versatility is done by fixing the processor to a business card sized card. This card is called a processor card
How can you skip chapters on Carnegie learning?
you can skip, your teacher has a Carnegie tool on her computer that controls everyting, you can see how long you where in a chapter, the chapters,a dn sections you have done ect.
The steering wheel controls for the DIC on 2004 Silverado stopped working but the radio controls still work HELP?
The first thing to look for is a blown fuse. Then there should be a master reset done on the computer to reset the error this should resolve the problem.
What are the four steps for correctly soldering components to a printed circuit board?
1. Remove the soldering iron from the holder and wipe the tip on a sponge. 2. Heat the joint to be soldered. 3. Apply solder to the joint. 4. Apply a small bit of solder to the tip of the soldering iron and return it to the holder.
How do you replace a tail light circuit board in a 1999 Jeep grand Cherokee Laredo?
Most people would say it can not be done. but if you don't minde playing around with the tail light, I think the Circuit board will come out with the back plate but it will take abit of work prising it off as it is glued on. But then you would have to get an used tail light that has broken lenses and good sockets
How do you repair Renault Megane electric window?
hi, i found on mine the actual mechanics are fine , it is the attached circuit board plugged onto the window motor that controls the speed and direction that was gone ,only problem is you need to buy the complete unit , just to unplug the connector you need, £225.00 plus vat, i bought one from a scrap yard, £40.00 complete, changed the plug holding the circuit board job done , i got a 2005 megane 1.6 16v . hi i have a 53 plate megane and i dryed the wires with hair dryer and it worked Renault are really bad for water in the electrics
What problems do programmers have when building a computer so that they can follow instructions?
Programmers do not build computers, they programthem.Computer Engineers design computers, then other people build and test them.There are no problems in designing a computer so that it can follow instructions, its just state machine and logic circuit design, which if done right then the computer design works. If done wrong, you redo it.
