answersLogoWhite

0


Best Answer

Turn off the pump first. Then remove the hose and vacuum head.

User Avatar

Wiki User

โˆ™ 2015-07-14 16:09:00
This answer is:
User Avatar
Study guides

What is a balance equation

Is hair perm lotion an acid

How do you adjust the pH level of pool water

Is shampoo an acid or base

โžก๏ธ
See all cards
3.94
โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…
16 Reviews

Add your answer:

Earn +20 pts
Q: After vacuuming the pool do you take the hose and vacuum head out of the pool before or after turning off the pump?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

When vacuuming the pool why would the pressure be so heavy it sticks to the bottom of the pool and then loses pressure?

As you vacuum the bottom of a pool you pick up a lot of fine dust and other material it is not unusual for a filter to block up while you are vacuuming. cleaning the filter or a brief backwash will probably fix the problem RB The answer above did not address the question. The vac head needs to have the wheels adjusted if it is a wheeled vac head. If the vac head is a brush model then you need to reduce the suction some. To do that you need to open the 2nd skimmer some -if you have one. Otherwise, you have to somehow throttle down the suction when you vac pool. I had a similar problem with my vacuum in a vinyl pool. The head was too close to the liner due to the bristles being worn down. Replacing this with a vacuum head that has both casters and bristles made vacuuming much easier and more effective (no more wrestling with the vacuum). http://www.walmart.com/catalog/product.do?product_id=10927854


How do you vacuum an above ground pool?

Before vacuuming an above ground pool you should make certain the water level is mid-way up the skimmer mouth (opening).To manually vacuum an above ground pool, typically you:Insert the vacuum head onto the end of a telescopic pole.Attach one end of the vacuum hose to the vacuum headRemove the skimmer lid and skimmer basketIf you have a vacuum plate, install it.While holding onto the telescopic pole, allow submerse the vacuum head and let the vacuum hose float on top of the pool waterStarting at the end of the vacuum head closest to the vacuum head start feeding the hose down a foot or so into the water.Continue to do this until the air is out of the vacuum hose.Cup one hand over the end of the vacuum hose while putting it into the skimmer either on the vacuum plate or the opening at the bottom of the skimmer.The pump may lose prime but will generally pick prime back up within 10 - 15 seconds.


How do you vacuume an above ground pool?

Before vacuuming an above ground pool you should make certain the water level is mid-way up the skimmer mouth (opening).To manually vacuum an above ground pool, typically you:Insert the vacuum head onto the end of a telescopic pole.Attach one end of the vacuum hose to the vacuum headRemove the skimmer lid and skimmer basketIf you have a vacuum plate, install it.While holding onto the telescopic pole, allow submerse the vacuum head and let the vacuum hose float on top of the pool waterStarting at the end of the vacuum head closest to the vacuum head start feeding the hose down a foot or so into the water.Continue to do this until the air is out of the vacuum hose.Cup one hand over the end of the vacuum hose while putting it into the skimmer either on the vacuum plate or the opening at the bottom of the skimmer.The pump may lose prime but will generally pick prime back up within 10 - 15 seconds.


Where is the vacuum in a vacuum cleaner?

inside the vacuum head


What is the maintenance procedures for taking care of Mannington flooring ?

Sweeping and vacuuming the floor regularly is one of the procedures but the vacuum must have a brush head. Do not mop the floor or flood it with water. You should try to always use Mannington maintenance products.


Why does my vacuum head frequently suck so hard that it sticks to the bottom of the pool while vacuuming?

you need a bypass most pools have 2 skimmer's if yours has only one you can get an adapter were it hooks up to system to relieve the pressure you can damage your pump if you do not correct this soon


What pool vacuum is better for a vinyl pool?

A vacuum head that has a brush on the bottom - no wheels.


What is turning the head as when saying no is an example of?

rotation


Turning the heAd as when saying no is an example?

rotation


Why does your tap turn but water stays on?

If you are turning the head part continuously and the water is not turning off then the head part has stripped and needs replacing


How do you switch the pump over when you want to vacuum the pool?

Normal procedure for vacuuming. With pump running,connect vac hose to vac head and lower into to pool (on vac pole), filling hose with water (push hose into water, hand over hand, to fill). When you get to the end of the hose you should see it full of water. Connect end of hose to skimmer - remove basket and push ed of hose into suction hole in skimmer. Suction should now be via the vac head - you're vacuuming. Contact me by e-mail if you need more info.


What are Phillips head screwdrivers used for?

For fitting into and turning phillips head screws.

People also asked