answersLogoWhite

0


Best Answer

Removing the rear seat is only one step in fuel pump removal.This lets you access the connections only.To actually remove the pump,the tank has to be removed.This procedure can be a pain if you have big hands.

User Avatar

Wiki User

โˆ™ 2005-10-22 19:44:52
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Can you get to the fuel pump on a 2000 Ford Contour if you remove the back seat and does it take any specialty tools to change out?
Write your answer...
Submit
Related questions

How do you remove the comperssion rings on a 1974 VW Beetle?

There are specialty tools available to make this alot easier,piston ring expanders or pliers will help remove and install rings.


Is it necessary to remove water pump to replace the crankshaft position sensor on a 1998 La Sabre?

no but you will be in need of specialty tools


What tools do you need to change battery on dodge stratus?

A jack, tools to remove the left wheel. wrenches and sockets to remove fender liner and battery.


How do you repair outer tierod end?

Remove old one and replace. Several specialty tools are required. The last step is a front end allignment.


How do you change the front brakes and the back brakes on a 1999 Alero Oldsmobile?

First of all, Do you have any specialty brake tools? Ben


What is the procedure to change lower ball joints on a 1998 Ford Contour with 2.5L V6 engine?

You can do it with special tools and a manual on your car from the parts store or autobooksonline.com


How long would it take to drop the oil pan to change the gasket on a 2000 contour?

having all the required tools and spares available, no more than an hour


Where is the orifice tube located on a 1996 Ford Contour Sport?

on my 1999 Ford Contour the oriface tube was located under the hood on the firewall on the high pressure line, below the larger low pressure line, need to buy disconnect tool fuel/ac line tools, remove and then along the line is a connection with two nuts 22mm and 19mm unscrew and remove hose


What tools are needed for oil change?

The tools needed for an oil change tend to be common tools. A floor jack is needed to access the oil pan. A pan which is used to drain oil into. A wrench and socket set is used to remove and replace the oil cap.


Are Irwin tools made in the US?

Most os the hand tools are made in China with some specialty tools made in other countries outside the US. Power tools made in China.


What kind of website is GearWrench?

GearWrench is a website that sells tools. These tools are mainly automotive like torque wrenches, pliers, wrenches, screwdrivers, nut drivers, and specialty tools.


What tools are required to change starter on 96 Saturn?

To remove car parts, a person must have the right tools. For a person to remove a starter on a 1996 Saturn they would need a 1/2 inch socket, a 4 inch extension, a wrench, and pliers.Ê


What products and services are offered by the company JET Equipment and Tools?

JET Equipment and Tools offer a variety of hand tools air tools, and abrasives. They also offer Strongarm, specialty automotive, and material handling services.


How do you get cm in Microsoft office?

Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.Change the measurement units under Tools and options.


How do you replace the brake light cover to change bulb in suzuki aerio?

In the trunk in back of where the light is located there is a plastic lining. remove that, usually they just pop out with out tools, behind that you will see the how to remove the light. It is quite easy. make sure you have the proper tools to do so


What kind of tolls does Lisle specialize in?

The Lisle Corporation specializes in a variety of different tools and products including: specialty tools, creepers, and lubrication and tire products.


What is a Estwing hammer designed especially for?

Estwing hammers are designed especially for high end striking and being used as struck tools, roofing tools, geologist's hammers and various specialty striking tools.


How do you change backing plates on a Chevy Trailblazer?

You must remove the axle to replace the backing plates. It is job for the professional do-it-yourselfers with all the tools.


What tools do you need to remove the wheel cylinder on a 1993 Pontiac Bonneville?

what tools do i need to remove the wheel cylinder on a 1993 pontiac bonneville


What are some good spy tools?

There are several spy tools that can be bought by the public. The best spy tools are small cameras, video recorders, and voice recorders. These can be found online and also in some specialty stores.


What tools are needed to change the front brake pads for a 1999 ford contour?

Generally you will need basic metric wrenches, and metric sockets and possibly a torx head socket on some models. Also jackstands and hydraulic jack.


How do you change the front struts on a 1996 Ford Explorer?

1996 Explorers do not have front struts. They use torsion bars as springs that require special tools to remove and conventional shock absorbers that are easy to remove.


What tools do you need to remove the battery from a 2005 harley sporster?

Common hand tools.


What tools do you need to remove a starter for 94 Oldsmobile achieva?

Common hand tools.


What tools do you need to remove the crankshaft pulley pn 1995 Honda Passport?

What tools do you need to remove the crankshaft pulley on a 1995 Honda Passport?

Study guides

๐Ÿ““
Create a Study Guide