answersLogoWhite
Ford Thunderbird

Can you put a 1994 thunderbird motor in a 1996 thunderbird?

123

Top Answer
User Avatar
Wiki User
2010-08-31 06:11:22
2010-08-31 06:11:22

Can you put a 1994 thunderbird motor in a 1996 thunderbird?

1

Related Questions

User Avatar

1994 TBird has an R134 system. You can buy charge kits at any auto parts store. How do you put freon in a 1994 Ford Thunderbird Lx coupe so that the air conditioner can work?

User Avatar

Yes, you can put just about any motor in any vehicle, it just takes time, and knowelge (and money helps too). The 6.0L 367 is a pretty popular swap for the 88-98 Chevy/gmc trucks and SUVs If you mean a 96+ up motor, then no, 1996 gm introduced the vortec motor to the world and is not compatible with 95 and down applications, unless the computer and fuel systems are upgraded along with it. Your 1994 Chevy 3/4 ton has a 5.7L 350 not the Vortec 350 introduced in 1996.

User Avatar

Put the new motor mount bushing into the appropriate place. Put the motor mount retaining bolt in. Let the engine down from the jack. Tighten the motor mount bolt.

User Avatar

motor is the same, transmission is diffrent... you need just the motor or you get a manual body but auto swap?

User Avatar

??...i would say the kind that lubricates...??

User Avatar

In a 1996 Ford Taurus ( 5W-30 ) according to the Owner Guide

User Avatar

ford didn't put a 4.7l in a ford t bird the firing order for a 4.6L that they did use is 1,3,7,2,6,5,4,8

User Avatar

have take motor and trans out 1996 Honda accord put timing belt

User Avatar

According to the owners manual - 5.3 U.S. quarts ( 5.0 liters ) with filter change

User Avatar

First you will have to take the motor out and separate the Transmission from the motor, then you have to take the clutch off of the flywheel and put the new one on with an alignment tool, then you put it all back together.

User Avatar

you take the mounts of and put new ones on dah

User Avatar

It is possible, but there is a large difference in the dash/wiring/etc. Besides the dash, the wirhing harness for the dash as well as the harness for the motor and the radio harness will need to be changed.

User Avatar

first you need to see if u can put a manual pump and a rod if so just put a carburetor intake on your motor and a vac disturber on it

User Avatar

WEll it all depends on the fuel system on the truck and motor if hey are the same u should be good... but one may be a tbi system and that's where u might need to do a little tweaking on your set ups.

User Avatar

I have a 94' Q45 motor and transmission in my 1991 Q45 - so the answer is "probably".

User Avatar

The easiest way would be to get an entire wiring harness/ECU from the 1994 and put it into the 1988 with the motor. This will eliminate any splicing or cutting you may need to do otherwise.

User Avatar

Disconnect the battery. Remove the door panel. unbolt the door lock motor, and remove the wiring plug. Replace the motor and put the panel back on.

User Avatar

yes, u can make anything fit if you know what you are doing

User Avatar

Yes you just have to take the plug out of the head to put in the distributor.

User Avatar

if its a 1987-1994 unhook the coolant tank unplug heater motor and 5 or 6 bolt off heater motor and you are done to put on reverse process


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.