the wire is bare how do you replace the wire with out removing the dashboard on a 1993 Chevrolet corsica?
Begin by removing the dashboard instrument panel cover. Take hold of the dashboard lightbulb, push in and turn at the same time. The dashboard lightbulb will come out. Reverse the process to install your new dashboard lightbulb.
Remove the dashboard cover. The dashboard cover can be removed by removing the retaining screws. Remove the light retaining nut. Remove the light bulb.
As of right now there are unfortunately no known financial assistance programs in any state to help in removing asbestos from households .
The Chrysler 300 dashboard is held in place by 12 retaining clips. Pry outward on each retaining clip, one at a time. The dashboard will come off.
Turn on the dashboard lights, and start removing the fuses one by one. When the dashboard light turned off, that is the good fuse. If the dashboard fuse is burnt, start replacing the fuses one by one, and when the dashboard will light up that is the place of the burnt fuse.
Begin by removing the instrument panel cover from your 2002 Pontiac Montana. Take hold of the dashboard lightbulb, push in and turn at the same time. The dashboard lightbulb will come out. Reverse the process to install your new dashboard lightbulb.
This is a tedious job and static electricity can ruin the printed circuit. TAke it to a garage.
The struts on a 2004 Ford Expedition are replaced by jacking the vehicle up, removing the wheels, and removing the strut retaining bolts. The old struts can then be removed and new struts put in their place.
A Vauxhall Tigra has dashboard lights that are important for reading the measurements at night. These can be replaced by removing the old parts and installing the new ones.
The dashboard on a Cadillac DeVille is removed by pulling up the trim, removing the retaining screws, and lifting it from its pointing points. It can then be gently lifted at an angle to remove it.
You can remove the dashboard from a Mitsubishi Triton by removing the retaining clips. There are 6 retaining clips. Two clips on each and of the dashboard and two clips in the middle.
You can remove the dashboard in your 1976 Chevy Caprice by removing the dashboard retaining bolts. After the retaining bolts are removed pry outward on each retaining clip.
Instructions1 Open the Camaro's hood. Make sure the engine is off and remove the black terminal from the battery with a wrench.2 Remove the two screws under the steering wheel with a Phillips screwdriver.3 Remove the two screws on the far left of the steering wheel on the side of the dashboard. Remove the two screws on the far right of the dashboard, to the right of the glove compartment.4 Open the glove compartment and remove the two screws at the back of the compartment. Pull the glove compartment off the dashboard.5 Remove the four screws from the corners of the center dash panel. Remove the screws along the edge of the dashboard, close to the windshield. Once all of the screws are removed, pull up on the dashboard to remove it from the Camaro.Tips & WarningsIf you are having a difficult time removing the dashboard from the Camaro after removing the screws, use a flat-head screwdriver to assist you in prying it off the Camaro.Be careful not to break the dashboard when pulling it off.
It will easily snap out with a flat head and work from one end to other removing it carefully.
the HEATER CORE can be removed by removing the dash. how do i ghange the dash
It is in the heater box under the dash and it usually means removing the whole dashboard assembly.
Begin by removing the instrument panel cover. Take hold of the dashboard lightbulb, push in and turn at the same time. The lightbulb will come out. Reverse the process to install your new dashboard lightbulb.
You get to the rear air fan motor in a 2004 Ford Expedition by removing the bottom of the glove box. You will then see the motor housing, and a clip that you must remove to get to it.
I have recently removed a 1992 Chevrolet Silverado dashboard from a junkyard truck, and also my '92 Chevrolet Silverado dashboard from my fathers truck and installed the new one I removed from the junk yard truck...let me just inform you, it's not easy. Start at the bottom removing those screws and work your way up is my best suggestion.
Begin by removing the instrument panel cover from your Mercedes-Benz E430. Push the lightbulb in and turn it at the same time. The instrument panel lightbulb will come out. Reverse the process to install your new dashboard light bulb.
Apparently the last guy that answered this was a jerk. Just removing his comment. Sorry I am not answering your homework for you.
The fuel pump shut-off switch for a Ford Expedition is located in the passenger kick panel below the glove compartment. It can be accessed by removing the trim and outer panel.
There is Four(4) bolts on each catalytic converter. Your expedition has two cats installed. Removing these bolts may be difficult due to corrosion so take a grinder to them for a quick process.