No, the mA rating of adapters is the maximum amount of load that can be drawn from the adapter. 1 amp is equal to 1000 mA. By replacing a 800 mA adapter instead of using a 1000 mA adapter is limiting the connected devices load by 200 mA. If the connected device draws 800 mA's or less then the adapter will work.
It depends on the requirements of the device being powered. If the device only requires 1200mA then yes it can be used. If it truly requires 2 amps than it will not function properly and could damage the power adapter. 1200mA is 1.2 amps, this power adapter actually has less power available than the 2 amp version.
No. You can always increase the mila-amps (mA) but not lower them. Also if the polarity of the plug isn't correct, you can cause permanent damage to your equipment.
It will be fine the device will only draw what it needs
Yes, if the connector is the same then the higher current adaptor should be fine.
Yes, but be sure the connector polarity is the same (or cut and resolder to correct that). Also, not all adapters are AC/DC, some are AC/AC (9vac vs 9vdc).
Yes, as long as the capacity of the adapter is larger than what the device needs to operate it will work nicely.
No, the power adapter has to match the power requirement.
Yes, the supply of 500 mA will supply a 300 mA device very nicely.
According to google if you have an automatic universal adapter, that adapter will automaticly find and adapt itself , the polarity ,voltage,amper , so that means an adapter can adapt polarities as well as voltage and current. A manual universal adapter on the other hand you have to adapt the polarity manually on the adapter itself , by checking what the device you wanna power has positive or negative, most electronic devices presently use positive . Check and see what voltage , amper and polarity a device needs. Positive : +--o)--Minus , Negative : Minus--o)--+ Or Positive: Minus--(o---+ , Negative : +---(o---Minus And adjust manually to what is required.
Depending on what we're talking about here, most devices will tolerate +/-15%, or in your case, 7.65v to 10.35v. A 6V power supply will only give the device 66% of the power it's rated for (not enough). Even if you could find an adapter that would fall within the 15% tolerance, it's not a good idea to try it. A multi-voltage adapter can usually be purchased for cheap at your local RadioShack or if you're feeling lucky, you might be able to find one at any place that recycles electronics (Goodwill or any local recyclers).
Not normally. It takes a 9 volt AC adapter. If you were to get something to replace that that ran on batteries, it could.
You can't. You have to use the pedal's AC adapter or a Voodoo Lab Pedal Power AC. Pedal Power 2 is a DC unit; the Whammy is an AC unit.
A power supply that produces 1.8 amps is the same as saying 1800 mA. What has to be taken into account here is if the voltages are the same. If the device that uses 700 mA has a specific voltage to operate on can the power supply provide the same voltage. Another factor to look at is , both the device and the power supply have to match their AC or DC requirements. One can not be AC and the other DC or vice versa.
No, the adapter's power output has to be equal to or greater that the current draw of the device.
Yes. There's a subtle difference in the meaning of the "--- ma" labels on the two units:-- On the "device" ... the unit that uses power ... the "200ma" is the current it useswhile it's operating.-- On the "adapter" ... the unit that supplies power ... the "800ma" is the maximumcurrent that it's able to supply. Anything less than that is easy.So your adapter is OK to operate your device. In fact, with suitable wiring and a bit ofcooling, it could nominally operate 4 of them at the same time.
No. The device will try to draw 700 milliamps which will overload the 300 milliamp adapter most likely causing it to burn out and possibly catch fire.
The capacity of the 800 mA adapter is 200 mA larger than the 600 mA adapter.
Yes you can. But it may damage your computers power supply.
Sportcraft / Unicorn Part# 79534 "AC Adapter - 9V/800MA" 9 Volt, 800MA +/- AC adapter See attached image of official parts re-order form and manual.
No, a power adapter must supply the same voltage, same polarity, and at least as much current as the load requires. Your adapter can only supply 300mA, which is less than the 700mA required by the load.Your game probably will not turn on and the power adapter may be damaged.
Most probably you are using a AC (117V or 220V) to DC 6V converter adapter. If yes, then the answer is no, you cannot use a lower current rating for a device that draws more current. If you plug in a device that needs DC 6V 500 mA to an adapter that can only supply DC 6V 300mA, then the adapter could start sending higher than 6 volts current which may damage your equipment or overheat the adapter. If you are using a higher mA rating adapter, then it's okay. For more technical details, see: http://www.jaycar.com.au/images_uploaded/plugpack.pdf
I think you mean to ask if one can use a 9v 600mA adapter to power a 9v 300mA appliance. Yes, you can do that. A 9v 600mA adapter will deliver 9v at up to 600mA. A mA is one milli amp, or one thousandth of an amp. 300mA is 300 thousandth of an amp, 300/1000 or 0.3 amps. 600mA is 600 thousandth of an amp, 600/1000 or 0.6 amps, and is twice the current of 300mA.
Using an undersized power supply is not a good idea. The device drawing 850 mA being connected to a 800 mA source will work but the adapter will get warm to hot over a period of time. This overloading of the power supply will eventually destroy the adapter.
Yes, you can run a 4.3v device with a 5v power adapter as long as the amperage of the 4.3 volt device is under the amperage capacity of the 5 volt adapter.
You would overload and damage the device and/or the adapter.