A 9V 1A adapter will supply up to 9 Watts of power and a 9V 200mA adapter delivers up to 1.8W of power. The 200mA adaptor may not be able to supply enough power to a device that has been supplied with a 1A adapter. The 1A adaptor should operate equipment that originally used a 200mA adapter.
Before using a different power supply, check that the outputs are both DC or both AC. If they are both DC, it is important to check that the polarity at the connector is the same for both. If AC and DC supplies are swapped or the polarity is swapped there is a risk that the equipment will be damaged.
Can a 4.5v 200mA adapter be substituted by a 4.5v 1200mA adapter
No, a 100 mA adapter's maximum output is 100 mA and it does not have enough capacity to supply a 200 mA load.
Yes, there is more than enough capacity in a 300 mA adapter to operate a 200 mA device.
no it can not
No, the capacity of the device is too large. The adapter will heat up and may even burn its internal windings open.
No, the 30 mA one is the more sensitive because it is the only one that will operate at currents between 30 and 100 mA.
If a 200 mA power supply is used on a circuit needing 2 amp it would overload the power supply. Two amps equates to 2000 milliamps. Trying to pull 2000 milliamps from a device that is only capable of supplying 200 milliamps is not advisable. The excessive current draw would most likely burn the wires open and render the power supply useless.
10 ma times 50 ohms is 0.5 volts. 0.5 volts is one two hundreth of 100 volts, so the multiplier resistor on 200 time 50, or 10,000 ohms.
V=RI or I = V/R so I = 0.4/100=0.004A or 4mA
It sounds like the same thing to me.
The capacity of the 800 mA adapter is 200 mA larger than the 600 mA adapter.
Yes, a 9 volt 1600 mA AC adapter can be substituted for a 9 volt 300 mA adapter. The mA number represents the highest allowable current to be drawn from the adaptor. The adaptor that you want to replace has only 300 mA maximum capacity. The new adaptor has five time the capacity of the old one which means that devices that draw up to 1600 mA can be connected to it. Depends on what you are pluging into.. if could possible run unit hot..
Yes you can. All the 1300 mA rating means is that adaptor can supply devices up to 1300 mA. The old adaptor's limit was 800 mA. The new adapter has 500 mA more in reserve if it is ever needed.
Yes, the maximum that the adapter can deliver is 1300 mA or 1.3 amps. The maximum that the device will draw is 200 mA or .2 of an amp.
Yes, it would actually be a little heftier power supply as to how much amperage it could draw without blowing out the internal fuse.
No it will not harm the plug in device. The 1 amp relates to 1000 mA or in other words it has five time the capacity as the 200 mA adapter.
It depend on what the load of the device that plugs into it is. The mA rating is the maximum amount of amperage that the adapter can produce. The 500 mA adapter will produce about a half amp whereas the 1200 mA adapter outputs 1.2 amps. So one is about three times larger that the other. Check the device that you are trying to power for a mA load and that will tell you whether you can use it on the 500 mA adapter.
A one amp adapter is the same as a 1000 mA adapter. If your device requires 500 mA to operate then there is ample capacity in the adapter to operate a 500 mA device. Be sure to match the type of voltage AC or DC from the adapter to the driven device. Both have to be the same.
Yes
Yes, the rating of the adapter is the maximum amount of current allowed to be drawn from it. The adapter you state has a maximum of 1000 mA or 1 amp. If the device draws 700 mA's you will have 300 mA's of spare capacity.
No, the replacement adapter has to be of an equal or greater value but never lower.