0
Can you wire two 220V devices off of one 50A GFCI breaker where the total load is 38A?
Wiki User
∙ 15y ago
No, only one GFCI per circuit.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Can a circuit with a GFCI be shared at the box?
Your question is a bit vague, but let's try a two part answer. If you have a GFCI breaker in an electric panel you should only have one connection at the breaker, but the breaker will protect all devices on the circuit. If you are talking about a GFCI outlet, they are equipped to extend the GFCI protection to other non-GFCI outlets by using the proper "output" connection on the GFCI.
Is a GFCI breaker required for an electric pool heater?
I'm not positive but, as far as I know, one is required on a 120V heater but not on a 220V heater. Even if a GFCI isn't required I would install one anyway for the safety of your family and friends. These devices do work and are well worth the cost. Call a Professional... Either a GFCI outlet or a GFCI breaker, and I think I'd use the GFCI outlet because the reset on an outlet is closer to the pool than the breaker would be. But put it far enough away from the pool that you've got to get out to reset it. I think that's code; if it's not it should be.
Do you need a gfci outlet if you have a gfci breaker?
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
A GFCI device in a breaker is intended to?
A GFCI device in a breaker is intended to trip the breaker open when a ground fault is sensed in the circuit that the breaker is protecting.
Does anyone make a 100 amp GFCI breaker?
Not that I know of. The largest GFCI breaker I have seen is a 60 amp.
Are gfci receptacles required in kitchens?
No, you could use a GFCI circuit breaker instead.
Is a ground fault indicator outlet installed at the breaker box?
There are tow places to put a Ground Fault Circuit Interrupter. There is a GFCI breaker which would be installed in a breaker box and a GFCI outlet that can be installed anywhere. Most GFCI outlets allow you to connect regular outlets to the GFCI and those outlets will also be protected.
How do you trace earth fault?
The methodical way is to remove devices one-by-one from the circuit and after each device is removed, reset the breaker or GFCI and see if it still trips.
Why does your gfci keep tripping after 15 minutesI suspect the circulating motor in my spa.?
The GFCI is sensing stray electricity. Usually, there is no GFCI connected to the pump motor. The GFCI devices would be associated with the air blower, or the lights. If it is the circuit breaker, then there may be a problem with the circulation pump or the circuit breaker itself. A qualified electrician will be able to locate and correct the electrical problem. A pool repair tech may be able to do the same and also correct the problem if it is the motor. Ken
Are gfci plugs required in a bathroom?
Deoends on code you are governed by. In USA, a GFCI outlet or a circuit controlled by a GFCI circuit breaker would be required.
Why and when would you use a GFCI breaker within a older home with a groun?
You need a GFCI outlet at any location that is within 6' of a water source. You also need a GFCI outlet in a room with a concrete floor, any garage, and any location outside the home or under the home in the crawl space. A GFCI outlet protects you from electrical shock near water or moisture. You can protect more than one outlet with 1 GFCI outlet. Connect the incoming power to the LINE side of the GFCI outlet and all the other outlets getting power from that outlet to the LOAD side of the GFCI outlet. That way they will all be protected by 1 GFCI. A GFCI breaker is used to protect an entire circuit and not just individual receptacles. It is often cheaper to use GFCI receptacles than a breaker, especially if "piggy-backed" such as described above. It is also more convenient to reset a GFCI receptacle than to reset a breaker. But your question is "why." From this I suspect you may be misunderstanding the difference between a breaker and GFCI protection. To keep things simple let me say that a GFCI does not work on the same principles as a standard breaker. It provides a much safer protection than a standard breaker. Even with a ground you need GFCI protection as listed above.
What is a ark fault circuit breaker?
install breaker in panel and put the hot wire on the breaker and also there should be a place for the neutral on the breaker also both wires will be landed on the breaker in different spots and then take the white wire that is coiled on breaker and land it on the neutral bar
