Best Answer

19ft/lbs, but i set my slip wrench to 20ft/lbs.

The plug head is a 15mm on mine.

User Avatar

Wiki User

โˆ™ 2013-03-30 22:37:21
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: Chevrolet Colorado i5 oil plug torque specs?
Write your answer...

Related Questions

Specs for Oil Drain plug Torque caterpillar 3406?

The oil drain plug torque is 65ft lbs

What are the spark plug torque specs for a dodge 4.7 motor?

20 ft.lbs.

1998 ford ranger 3.0 spark plug torque specs?


Torque specs for spark plug on f250 5.4 liter?

28 foot pounds

Hyundai elantra oil drain plug torque specs?

25-30 lb-ft

Locate radiator drain plug on 2005 Colorado Chevrolet?

There is no drain plug, you have to remove the bottom hose.

What are the spark plug torque specs for a 2000 dodge stratus?

20 ft lbs. this is a correct answer from the manual and the gap spacing of the spark plug is .044 :) Cindy

Torque specs. for 1990 Ford Ranger 4.0L?

spark plug gap on 1990 ford ranger 4.0?

What is the spark plug torque specification for a 3.0 2002 ford ranger?

It depends on what type of spark plug you have. Go to to see a guideline of torque specs for plugs. Those are from NGK, but will cover any other spark plug as well.

What is the spark plug gap on 2004 Chevrolet Colorado?

Listed in owner's manual and under the hood on a placard.

What is the torque specification for the oil pan plug on an 2008 silverado with 5.3L aluminum block?

Can't find any specs. For drain plug, just make sure its tight.

Where is the radiator drain plug for 2006 Chevrolet Colorado?

The cooling system on these vehicles is drained by detaching the lower radiator hose from the radiator. The radiator doesn't have a drain plug.

What is the torque specs on the oil drain plug on a 2006 Trailblazer 4.2L?

19ft lbs for most men, this can also be achieved using the two finger rule two fingers on a 6-8 inch socket wrench ... turn till plug is snug

Does 1991 Thunderbird torque converter have a drain plug?

does a 1991 thunderbird torque converter have a drain plug

2000 Jeep torque converter drain plug?

A 2000 Jeep does not have a torque converter drain plug.

What is 2.2 ecotec engine oil drain plug torque specs?

For 2.2L Ecotec tighten the oil pan drain plug to 25 N·m (18 lb ft). The oil filter cap is also tightened to the same spec.

What is the proper procedure for changing spark plugs in a 1999 Mazda 626 ES?

Remove the plug wire from one plug. Do this carefully by twisting the boot on the plug and then pulling it off. Only pull the boot and not the wire. Before removing the plug use compressed air to blow out the area around the plug. Remove the plug and and replace with the exact same OEM plug which has been gapped to the factory specs. This is listed in the owners manual and under the hood on a placard. Before inserting the plug, coat the threads with anti-seize compound. Tighten the plug to the proper torque. Over or under tightening is a no no. Call the dealer for the torque specs. Replace the plug wire until you feel it pop or know that it is connected fully. Move to the next plug and repeat. Only do one at a time in order to prevent getting the wires mixed up.

What are the specs for a 2001 Toyota Sequoia for spark plug gap and torque?

For a 2001 Toyota Sequoia, the factory and spark plug manufacturer recommended gap is .032" (.813mm). The spark plug manufacturer's recommended torque for flat-seated plugs / aluminum heads is 20-30 n-M (15-22 ft lbs), but double check your owner's manual (if available) to be sure.

What is the torque spec for a 1995 1.0 Geo metro spark plug?

The 1995 Geo Metro spark plug torque specification is 20 pounds. You should torque the spark plug intent pound intervals.

98 Toyota Tacoma spark plug torque?

Spin them in by hand (remember the "Anti-Sieze" on each plug threads), then give them another 1/4 to 1/2 turn.I don't have the shop specs in front of me, but I thinkit is 14ft/lbs.

What is the spark plug torque for a 1994 Toyota Previa?

spark plug torque for a Toyota 2.4 is 95 inch/lbs

Where is the drain plug for the torque converter on a 2006 Chrysler town and country?

The torque converter doesn't have a drain plug on these vans.

How do you drain torque converter?

Some torque converters have a drain plug on them. Remove the rubber plug from the bottom of the bell housing. Crank engine a little at a time until the torque converter drain plug can be seen from the bottom. Unscrew the drain plug and drain the fluid. Put the plug back in.

What is procedure for oil pan gasket replacement on a 97 Saturn?

drain the oil from the vehicle, unbolt the oil pan, scrape old gasket from pan and crankcase. check the torque specifications for the oil pan bolts (shouldnt be very high). replace the gasket and oil pan to factory torque specs. put drain plug back in and fill with factory specs of oil.

How do you remove a t f from torque converter?

Some torque converters have a drain plug, others do not. With no drain plug the torque converter can be stood on its end once removed to drain it.