0
In an AC circuit the voltage and current are n the form of a sine wave that goes between a maximum and minimum value 60 times a second. Measuring the difference between these values is a peak-to-peak measurement. Root Mean Square (RMS) computes an average (mean).
To convert RMS to peak, multiply the RMS figure by 1.41. 1.41 is an approximation of the value of the square root of 2.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is the relationship between peak current peak to peak current and RMS current?
RMS is the root mean square value.(in alternating current only)
If a sine wave has a peak-to-peak current value of 10 Awhat is its rms value?
The root-mean-square (rms) value of a sinusoidal voltage or current is given by: Vrms = 0.707 Vmax and Irms = 0.707 ImaxSo, if the current has a peak-to-peak value of 10 A, then Imax will be half that value (5 A) , so the corresponding rms value is:Irms = 0.707 Imax = 0.707 x 5 = 3.54 A(Answer)
What is RMS Peak value and average value?
RMS is used to determine the average power in an alternating current. Since the voltage in an A/C system oscillates between + and -, the actual average is zero. The RMS or "nominal" voltage is defined as the square root of the average value of the square of the current, and is about 70.7% of the peak value.************************************************************The r.m.s. value of an alternating current or voltage is the value of direct current or voltage which produces the same heating effect.Fo a sine wave, the r.m.s. value is 0.707 x the peak value.The average value is different; for a sine wave it is 0.636 x the peak value.
What is the effective value of an AC sine wave current having a peak-to-peak value of 8 amperes?
The rms value of a sine wave current is 0.707 Imax. So the answer to your quesion is 0.707 x 4 = 2.83 A.
Why rms value of ac not peak value is used?
RMS (root mean square, 1.414) voltage of an AC (alternating current) sine wave represents its actual ability to do work. What can be converted to direct current, DC. Since the sine waves voltage (and current) varies constantly as it goes from zero to a peak through out its cycle it goes from no potential to a large potential to do work. The rms represents the power time of wave. The multiplier of 0.607 times peak gives the waveforms average voltage.
What is the relationship between peak current peak to peak current and RMS current?
RMS is the root mean square value.(in alternating current only)
The average value of a single sine wave of AC is 42.5amps. what is rms value?
Average Current = 0.636 * (Peak Current)so Peak Current = (Average Current)/0.636RMSCurrent = 0.707 * (Peak Current)so Peak Current = (RMS Current)/0.707Because both equations are in terms of Peak Current, we can set them equal to each other.(Average Current)/0.636 = (RMS Current)/0.707(42.5)/0.636 = (RMS Current)/0.707thenRMS Current = (0.707)(42.5)/0.636 = 47.24 ampsAnother AnswerSince the average value of a single sine wave is zero, you cannot calculate its r.m.s. value!
What is 10000 rms?
rms stands for root mean squared. rms voltage is a way of measuring a sort of average alterating current voltage as distinguished from peak-to-peak voltage. Likewise for ac rms current.
Why is the class A current less than the peak current?
Not sure what you mean by Class A current. Normally, when measuring AC voltage or current you either measure the peak to peak value or the Root Mean Squared (RMS) value. Since RMS is essentially an average measured over time, it would always be less than Peak to Peak value.
What is the effective current in an ac series circuit with a peak current of 20A?
Assuming a sine wave, the RMS current (the effective current) is the peak current divided by the square root of 2. In this case, that would be approximately 14 ampere.
If a sine wave has a peak-to-peak current value of 10 Awhat is its rms value?
The root-mean-square (rms) value of a sinusoidal voltage or current is given by: Vrms = 0.707 Vmax and Irms = 0.707 ImaxSo, if the current has a peak-to-peak value of 10 A, then Imax will be half that value (5 A) , so the corresponding rms value is:Irms = 0.707 Imax = 0.707 x 5 = 3.54 A(Answer)
AC or DC supply is given to a bulb which gives more illumination?
In AC supply, the RMS current is the effective current for power used in a resistive circuit. This is defined as the square root of the mean value of the square of the current, taken over a whole cycle. The RMS current dissipates power at the same rate as a DC current of the same value. A light bulb of course gives out light dependent on the current through the filament. So if the RMS current and the DC current are the same value, the light produced will be equal. With AC supply, the RMS value of current and volts is 1/(square root of 2) x the peak value, so peak value = 1.414 x RMS value. If you supplied DC at volts and current equal to the peak AC value, the power given to the light bulb would clearly be greater. Therefore to answer your question you have to specify what relative values your AC and DC supplies have.
Rms value of AC current is equal to main current at an angle?
The root-mean-square value is 0.707 times the peak value, for a sinusoidal voltage or current. Angle doesn't come into it.
What is RMS Peak value and average value?
RMS is used to determine the average power in an alternating current. Since the voltage in an A/C system oscillates between + and -, the actual average is zero. The RMS or "nominal" voltage is defined as the square root of the average value of the square of the current, and is about 70.7% of the peak value.************************************************************The r.m.s. value of an alternating current or voltage is the value of direct current or voltage which produces the same heating effect.Fo a sine wave, the r.m.s. value is 0.707 x the peak value.The average value is different; for a sine wave it is 0.636 x the peak value.
What is the effective value of an AC sine wave current having a peak-to-peak value of 8 amperes?
The rms value of a sine wave current is 0.707 Imax. So the answer to your quesion is 0.707 x 4 = 2.83 A.
Why rms value of ac not peak value is used?
RMS (root mean square, 1.414) voltage of an AC (alternating current) sine wave represents its actual ability to do work. What can be converted to direct current, DC. Since the sine waves voltage (and current) varies constantly as it goes from zero to a peak through out its cycle it goes from no potential to a large potential to do work. The rms represents the power time of wave. The multiplier of 0.607 times peak gives the waveforms average voltage.
Is starting current of a AC Motor measured as RMS or PEAK?
IT DEPENDS WHAT MEASURING INSTRUMENT YOU ARE USING. RMS - IF USING THE CLAMP AMMETER OR PANEL METER OSCILLOSCOPE - BOTH CAN BE READ
