Chevy Silverado
Peugeot
Peugeot 306
Nintendo

Could the drive shaft from a 1996 1.1 106 XN be used to replace one on the 1995 1.4 306 XL?

91011

Top Answer
User Avatar
Wiki User
Answered
2007-01-30 10:58:41
2007-01-30 10:58:41

Don't really think so, the 306 has one short and one long drive shaft with an intermediate bearing carrier. You could try a dirct comparison side by side.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


remove the distributer, remove the roll pin holding the drive gear onto the distributer shaft, remove the distributer drive gear, remove the shaft from the distributer to gain access to and remove the stator(pick-up coil). Replace the stator, and reassemble everything.

It's usually much more inexpensive to replace the entire drive shaft than to repair a worn cv joint. The new drive shaft will come with new cv joints and new boots.

it could be one of the sensors crank shaft or cam shaft

On Drive side It's On the bellhousing

iF IT'S A 2-WHEEL DRIVE THEN IT IS ON THE TRANSMISSION TAIL SHAFT HOUSING. IF IT'S A 4-WHEEL DRIVE THEN IT IS ON THE TRANSFUR CASE TAIL SHAFT HOUSING.

Remove the 4 nuts that hold down the U-Joints to the differential. Remove the 2 bolts that hold the center drive shaft carrier bearing to the frame. Put a pan or some kind of container under the tail of the transmission to catch any of the oil that drips. Then pull the drive shaft out of the transmission. If you decide to replace the u-joints, I strongly recommend that you take the drive shaft to a reputable u-joint specialist and have all 3 u-joints replaced and the carrier bearing all replaced and have the drive shaft balanced. Then put it all back together in reverse order. When removing the u-joints, make sure the transmission is in neutral and the parking brake is set and/or the wheels are blocked.

how to replace lower ball joints on 1995 4 wheel drive Nissan truck

Does it do it when you take it up to about 50 to 60 and then let off. If so then it could be your u-joints on your drive shaft.

you can, but it will require you to replace the output shaft on the '95 trans. with your old '90 model, as there is a worm gear built onto the old style output shaft to drive the speedometer cable. To replace the output shaft, you have to nearly completely teardown the transmission.

To permanently disable, remove the drive shaft from the transfer case to the front differential.

NO. The center shaft that runs through the transmission is longer on 4x4 transmissions so the transfur case will slide up on it. The tail shaft housing has NOTHING to do with it.

See if your drive shaft going to front end is bent.

There are many ways you could replace the fuel filter in a 1995 Jeep Grand Cherokee such as taking it to a garage. You could use the manual as a step-by-step guide as well.

Had one built for 1995 Chevy silverado z-71, rear, 65" balanced with my yoke, $275

Get a manual from a parts store and it has pictures and all.

Replacing the joint involves about the same amount of work and expense as replacing the shaft. Check with your local parts house for cost comparison. The left shaft for my 2001 cost me about $80.00 and required an hour & a half to replace. While you're at the store, pick up a repair manual.

The solution is easy. There is a little button that you press on the body of the switch that releases the 'shaft and knob'. A little jiggling is required sometimes.

I JUST RPLACED THE AXLE HALF SHAFT. YES IT IS ALWAYS ENGAGED. WHATS UP WITH THAT??

how to replace a starter on a 1995 Lincoln Continental


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.