how do you remove the wiper arms on a 2002 CRV?
removal of rear winshield wiper arm on 07 outback
You need a wiper arm removal tool. Look on ebay.
# Raise the rear wiper arm finish cap to expose the wiper arm nut. # Remove the rear wiper arm nut (1). # Lift the rear wiper arm assembly (2) away from the rear window and remove the wiper arm from the pivot shaft. The cap tilts up toward the arm
get a wiper removal tool and it goes under the arm and you just pry the arm up off the splines to take it off.
Under wiper arm flap is a grub nut, Undo nut and use a Wiper arm removal tool (there not expensive approx £10) Remove Arm and Replace with New
it just pulls up off of the splines on the motor stud, you can buy a wiper arm removal tool to make it easier to get off.
It is located fastened to the firewall just about iommeidiately below the hub of the right side windshield wiper arm.
To unlock the old wiper blades from the wiper arm you must slide the lock toward the passenger side of the vehicle. After this you raise the whole wiper arm. The old wiper blade then should come right off. Installation is reverse of removal.
Now I am working on this from the standpoint of my 1996, I assume they are the same. I could be incorrect: Look at the wiper arm from the bottom, you will see a small tab, if you pull the wiper away from the window, and then pull the tab to the bottom, you will lock the wiper away from the glass. if you bull the tab all the way out you will then be able to pull the wiper arm off from the pivot point. The hose is attached to the wiper arm by a clip, you can simply unclip it if this is a temporary thing, for long term removal, I am not sure as I have never had the desire.
Windshield Wiper Blade and Arm Front 1. Raise the cover over the wiper arm retaining nuts. 2. Remove the retaining nuts on the wiper arm pivots. 3. Match mark the wiper arms to the pivot for reinstallation. 4. Lift each wiper arm and free it from the pivot shafts. Ø The wiper arms will most likely be stuck, a useful tool for removal of the wiper arms is a battery terminal puller. The battery terminal puller exerts force on the pivot and raises the arm, otherwise prying and other techniques could do damage to the wiper arms, trim, windshield, or painted surfaces of the vehicle. To install: 5. Place the wiper arm onto the pivot aligning the match marks. 6. Tighten the wiper arm retaining nuts. Fasten the retaining nut covers.
Windshield Wiper Blade and Arm Front 1. Raise the cover over the wiper arm retaining nuts. 2. Remove the retaining nuts on the wiper arm pivots. 3. Match mark the wiper arms to the pivot for reinstallation. 4. Lift each wiper arm and free it from the pivot shafts. Ø The wiper arms will most likely be stuck, a useful tool for removal of the wiper arms is a battery terminal puller. The battery terminal puller exerts force on the pivot and raises the arm, otherwise prying and other techniques could do damage to the wiper arms, trim, windshield, or painted surfaces of the vehicle. To install: 5. Place the wiper arm onto the pivot aligning the match marks. 6. Tighten the wiper arm retaining nuts. 7. Fasten the retaining nut covers.
Windshield Wiper Blade and Arm Front 1. Raise the cover over the wiper arm retaining nuts. 2. Remove the retaining nuts on the wiper arm pivots. 3. Matchmark the wiper arms to the pivot for reinstallation. 4. Lift each wiper arm and free it from the pivot shafts. Ø The wiper arms will most likely be stuck, a useful tool for removal of the wiper arms is a battery terminal puller. The battery terminal puller exerts force on the pivot and raises the arm, otherwise prying and other techniques could do damage to the wiper arms, trim, windshield, or painted surfaces of the vehicle. To install: 5. Place the wiper arm onto the pivot aligning the matchmarks. 6. Tighten the wiper arm retaining nuts. 7. Fasten the retaining nut covers.