0
If the pressure of a wet vapour is ≤ 2000 kPa and the dryness fraction is ≥ 0.9, then (if you wish) you may use: Vx=XVg ; where Vx is the specific volume you are solving for, X is dryness fraction and Vg is the specific volume of the saturated vapour at the given state (pressure, temp, etc).
Otherwise use: Vx = (1 - X)Vf + XVg ; and in this case Vf being the specific volume of the saturated liquid at the given state.
The specific volume of wet steam is quite simply, the volume per given mass of the vapour at the given dryness fraction (or steam quality). In the case of wet steam it is solved for by a function of the relationship between the percentage saturated liquid, and the percentage saturated vapour in terms of specific volumes for the two obtained from a data chart.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Where do we use sleeve and cotter joint?
It is used in the connection of piston rod to the cross head of the steam engine, In the foundation bolt, Connecting two halves of fly wheel, Joining of tail rod with piston rod of a wet air pump
What is the effect of cooling load on wet bulb approach of a cooling tower?
Cooling load in kw is increase the temperature of the water before enter the cooling tower, thus the differential heat energy level is high compare to surrounding temp., so it will transfer heat more to surrounding and leave the tower with low temperature, and it will become more like to approach the wet bulb temp., this happens if the variables such the water flow, and the air velocity is kept constant.
How do you take the pump apart on a Ultimax -56 or is it a Ultra jet?
it depends what you are trying to access. you have to take out the four long bolts that are accessable from that back that run all the way up front that hold on the wet end. take off the front half of the wet end and you need to remove the propeller by threading it off by spinning it and holding the shaft from the very back with a large flat screwdriver the rest pulls apart. if you have to take it apart anymore... buy a new motor.
What is the difference between the Carnot cycle and the Rankine Cycle?
carnot cycle is a very ideal cycle that isn't practical at all , 'cause we add and reject heat isothermally , a wet mixture enters the turbine so it'll cause pitting and erosion and a wet mixture enters the pump , and the pump can't deal with a 2 phases fluid rankine cycle is a practical cycle but with a very low efficiency so the main difference lies in the adding and rejecting of heat
MQG Ball Mill?
The ball mill is widely applied in mineral classification, cement, fireproof materials, glass, pottery, chemical industry and so on. The ball mill can grind all kinds of rocks and grinding materials. There are two ways of grinding: the dry process and the wet process.
What is the effect of dry steam entry in to a wet steam filled vessel whether it promotes condensation in the vessel?
The effect of dry steam entry into a wet steam filled vessel will promote condensation in the vessel. However, it will be less wet because of the dry steam.
Why is dry volume different from wet volume?
Wet volume includes the vapor pressure of water, while dry volume does not.
How many kinds of steam?
There are three kinds of steam 1) saturated steam, 2)super saturated steam 3) wet steam.
Which is better wet steam or dry steam?
If by dry steam you mean superheated steam then dry steam because it has a higher calorific value
What is the difference between dry steam and wet steam to clean?
DRY steam is superheated There is a temperature below which steam will start to condense into water droplets. This is called the saturation temperature, and it varies with the pressure of the steam. Steam that is exactly at its saturation temperature is called saturated steam. Steam that is below its saturation temperature contains droplets of moisture and is called wet steam. Steam that is above its saturation temperature is called superheated steam.
What kind of state of matter is steam?
It is a gas, assuming you are talking about dry steam. If it is wet steam, it is both a gas and a liquid.
What is meant by moisture in steam?
whenever there is presence of moisture(water content) in steam due to which one cannot refer that steam as dry steam...then this type of steam are termed as wet steam!!
Is a wet/dry steamer flat iron really ok on wet hair?
A wet to dry flat iron is designed to use the steam that is created from wet hair.
How do you create steam from food?
Anytime you place something cold, wet, or frozen into a hot pan it will create steam.
What is meant by wet and dry steam?
Dry steam is superheated , meaning more heat has been added resulting in no liquid phase present and the heat of vaporazation has been surpassed adding to the total enthahpy of the vapor. Wet steam is much like the steam rising from a pot of boiling water.
A condensates return temperature indicates normal operation excessive steam defective trap or wet steam?
A condensates return temperature indicates excessive steam.
How is a boiling water reactor's superheater 'heated'?
They don't. BWR's run wet saturated steam. There is no superheating in a BWR, because there is no way steam would come in contact with a heat source. The plant must be built to be compatible with wet steam that could condense.
