0
Did they make a 8 inch harmonic balancer on a 1978 Chevrolet 350?
MacMcelroy
Yes they sure did. It could be a 4-bolt main engine.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
327 Chevrolet Harmonic Balancer Size?
a 6 INCH.
What size is a 350 Chevrolet harmonic balancer?
It should be 8 inch
How can i tell the difference between a Chevrolet 350Ci and a Chevrolet 305Ci 1986 in my C10 pickup?
the harmonic balancer on the 350 is about 10 inches in diameter compared to a 305 it has about 8 inch diameter on the harmonic balancer
What it the correct size harmonic balancer for a 1968 396 Chevy?
8 inch balancer.
Torque spec on harmonic balancer bolt on v8 350 eng?
The torque specification, for the harmonic balancer on your 350 cubic inch engine, is 280 pounds per square inch. The torque specification may vary according to the manufacturer of the engine.
How do you replace the harmonic balancer on a Chevy small block?
There is a bolt in the center of it, 5/8ths inch. Remove that, then the three 9/16ths bolts in a triangle pattern, which removes the pulley. Then, you will need a harmonic balancer puller, as they are pressed on.
Where is the harmonic balancer on a 1998 Lincoln continental?
the harmonic balancer is the crankshaft pulley approx6 or 7 inch diameter lower pully center of engine the serp belt is driven by power pulley also have a retaining bolt in center
Were is the crank sensor on a Pontiac grand pri?
The crankshaft position sensor is located behind the harmonic balancer. You will need a harmonic balancer puller and an impact wrench good for at least 750 ft pounds. Access the harmonic balancer through the passenger side wheel well. Remove the harmonic balancer center bolt and use the puller to remove the balancer. Use 1/4 - 28 X 3 inch bolts on the puller. The sensor is held with two screws. Be careful not to damage the weatherpack connector when releasing it from the sensor.
Where is the crankshaft sensor located on a 1991 Buick LeSabre custom?
to my knowledge it is located behind the harmonic balancer. You should be able to c the wires runing to it just to the right of the harmonic balancer. Now if you could help me with information on how to uninstall the harmonic balancer i would greatly appreciate it Thanks. To remove the harmonic balancer you have to buy or rent a harmonic bancer puller. The bolts required for yours may not be included. If not you will have to go to the hardware store and purchace them. You should use the 3 1/2 inch #8 1/4 inch bolt 3 required also buy 3 washers cost under 4 dollars.
What size socket fits on the large center bolt of the harmonic balancer on a 97 3.9 magnum engine?
1 1/4 inch1 1/4 inch
How do you remove the harmonic balancer in a 1995 Nissan Maxima GLE?
Start by removing the right front tire and support the vehicle with a jack stand. Then remove lower portion of the splash guard near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tensioner and then loosen the tensioner bolt (it is the one that's sticking straight up, you use a 14mm socket on it.). The power steering adjuster bolt will be accessed from the bottom near the power steering pump. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Remove belts. Then remove harmonic balancer bolt (19mm). If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller on to the harmonic balancer. (one finger on each side securely press into the belt groove.) The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.
Where is crankshaft position sensor on 97 buick lesabre 3.8?
The Crankshaft Position Sensor is behind the crankshaft pulley (harmonic balancer). You will need a ½-inch drive breaker bar and appropriate socket.
