answersLogoWhite
Ford Focus

Do 2002 Ford Focus have 2 lights on license plate?

789

Top Answer
User Avatar
Wiki User
2011-10-03 11:42:04
2011-10-03 11:42:04

yes 2002 Ford Focus do have 2 lights on license plate

1

Related Questions

User Avatar

hello i need you help me tell me how to remove the cover light from a license plate i have a ford focus se 2002 to put a new light thanks willie

User Avatar

Added to that, and assuming that you're asking because your license plate light is out, and because the fuse is the same fuse for the tail lights, then the problem is not the fuse. It's the license plate light itself. === It should be the same fuse as the taillights.

User Avatar

The license plate lights are located just above the license plate. Open the tail gate part way to make removal easier (unless you enjoy squatting). Remove the Phillips screws and replace the affected bulb.

User Avatar

prise the chrome cover down from left hand side

User Avatar

No because the licence plate light would only light up when you put the car in reverse. it is a seprate system. On the 2003 they are on the same fuse.

User Avatar

I have a ford focus 2001 hatchback and the problem seem to be a short circuit caused by the license plate lights. The fuse is burning when I'm turning the taillights on but if I take the license plate light fixtures out of the body of the car then the taillights are working. I'll try putting electrical tape around the metal parts of the license plate light and see if it's still burn the fuse (number 32, 10 amps).

User Avatar

There should be a connector for the lights above the rear bumper, but you may not want to disconnect it because then your likely to get pulled over for having a faulty license plate light

User Avatar

How do you change the lamp on the license plate of a lincoln ls 2000?

User Avatar

Changing the license plate bulb on a 2002 Lincoln LS is quite simple. You must first remove the license plate first. Then unscrew the old bulbs and screw in your new ones.

User Avatar

The license plate light and connected right above the plate on a 2002 Volkswagen Beetle. To replace it just unscrew the old light and mount the new bulb.

User Avatar

The tail lights and plate lights are on the same fuse, if the tail light come on it is not the fuse. Plate lights are not checked that often and it is common for them both to be brunt out when they are noticed.

User Avatar

how incomptent are you not to see the 2 screws holding the plate on????????????????

User Avatar

The license plate bulb is located right above the plate on a 2002 Oldsmobile Bravada. To replace the light simply remove the old bulb and install the new one.

User Avatar

You can replace the license plate light bulb on a 2002 Ranger by reaching under the rear bumper and pulling out the light socket. Remove the bulb and put the new one back in.

User Avatar

I have a 2002 LE. I accessed LP lights, by taking the trunk pad off. Be careful not to break the retaining clips. You can also go to Jiffy lube and have them replace the lights. Watch how they do it and you will know for future reference.

User Avatar

Unscrew license plate and remove to expose light fixtures. Wedge light module away from holes. Replace them and return them to sockets.

User Avatar

To change the license plate light on a 2002 Geo Tracker, remove the light lens with a small screwdriver. Take out the old bulb and replace with a new one. Tighten the screws on the light lens.

User Avatar

The license plate light bulb on a 2002 Pontiac Grand Prix is replaced by removing the retaining bolts and pulling the bulb out of its socket. A new bulb is then put into the socket and reassembled.

User Avatar

As the own manual states, the license plate bulbs can be replaced by first removing the plastic lens/dome that is covering the bulb. Turn it 1/8 turn anti-clockwise to unlock it. Then the bulb can be pulled out (straight, no turns). Push in the new bulb, clean it to remove grease and acid, and put the lens back on. There are two such lights. Joop Kaashoek

User Avatar

Using a sharpie marker, hold the license plate up the the front bumper and mark the bolt holes on the bumper and then using a drill gently apply pressure and drill through the bumper, be sure there are no wires behind where you are drilling and not to drill in too far, then attach the license plate with two bolts and nuts.

User Avatar

On my 2000 Hyundai Elantra, you can access the license plate lights from the outside. You use a flathead to pop out the right side of the light, twist the back end (where the wire comes out) and the part with the bulb comes out. Pull it out, slide the new bulb in, retwist it into its container and pop the light back in place. Repeat for other side. Cost me $3 for the bulbs and took me about 5 min to do.

User Avatar

Simplest solution is - locate the fuse that control the DRL circuit and pull it out.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.