answersLogoWhite

0


Best Answer

yes turn the water off and get someone to help you put in the water faucet

User Avatar

Wiki User

14y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

15y ago

yes

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Do you have to turn the water off before you can put on a new faucet?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why does my New faucet makes clunking noise?

There was air in the line. When you turn off the water with the faucet running make sure you turn it back on with the faucet open. That will release any air caught in the lines. That faucet shut with one on a lower floor on and restoring water does not work. Fast and easy. 1. turn on affected faucet 2. shut off water 3. turn water back on 4. faucet should be running smoothly now


How do you raise the height of an outdoor water faucet?

To raise the height of an outdoor water faucet, the best thing to do would be to get an extension for the existing pipe that will bring the faucet to the height desired. Remember to turn off the source of the outdoor faucet before starting this project. Remove the faucet valve, screw in the new pipe, replace the faucet valve. Sealing the ends of the new pipe with plumber's tape is also a good idea.


How do you install a bath faucet?

"Make sure you have the correct sized faucet and the correct tools. Turn off your water and then remove the existing faucet. Replace it with the new one, making sure it is sealed so that no leaks can occur when you turn your water back on."


Do you need to turn water off while replacing new bathtub faucet?

Yes, you certainly do.


How do you replace an outdoor faucet?

Shut of the water to the faucet. If a local shut off is not present then the main house shut off will have to be used, or the cutoff at the meter. unless plastic pipe is used then the faucet screws onto the water pipe. It will probably take a pipe wrench on the pipe and the faucet to break it free. use Teflon tape to cover the pipe threads before screwing on the new faucet. Turn the water back on and check for leaks.


No water flows from new bathroom faucet?

Did you remember to turn the supply line back on? Was there a plug that needed to be removed before connecting it?


What needs to be done if a rolling faucet has been replaced with a 2-handle faucet but the water pressure isn't as good as before?

what is the GPM rating from the old to the new the lower the GPM the slower the water. Sometimes there are restrictor discs (washers).


Can you use two water supply ouy lets with faucet?

There are always two hoses connected to a faucet. Hot & cold will have their own valves & stainless lines. (1) to each side. It's an easy hook up. Just turn off both valves, connect new faucet the same way & turn them on again.


How do you remove old shower pipes to install new shower faucet?

To remove old shower pipes to install a new shower faucet, turn the main water off first. Then either cut the pipes at the joints or unscrew the washers holding the pipes together.


What type of precautions should be taken before installing a new kitchen faucet?

One of the most important precautions to take before installing a new kitchen sink is to shut off water to the pipes in question. After that, it is key to make sure that you have all the necessary materials, and that the new faucet is attached properly, with no gaps or leaks.


How to Install a Kitchen Faucet?

If your kitchen faucet is old, leaking, or simply out of place amongst your new kitchen decor, it may be time to replace it. Here are the basics of how to install a new faucet as well as a few tips on making the task as easy as possible.Turn Off the WaterTo avoid a wet, sloppy disaster, make sure to turn off the water supply to your sink before tackling this task. If your sink doesn't have a specific shutoff valve, you may have to climb up to the roof and use the valve connected to your water tank. Once the water is off, turn on your sink faucet to drain any excess water from the pipes.Detach the Old FaucetA basin wrench is essentially for removing an old kitchen faucet and installing a new one. The coupling nuts that connect the faucet to its supply tubes are behind the faucet. Use your basin wrench to unscrew these. Once the supply tubes are disconnected, unscrew the mounting nuts that keep the faucet in place and lift the assembly slightly to reveal the nut attaching the sprayer hose to the faucet. Use your basin wrench to unscrew this nut as well.Position the New FaucetInstead of setting the new faucet in place then crawling under the sink to hook it up, connect as many connections to the faucet as possible before setting it in place, and then feed the lines down underneath the sink through the holes. This is usually possible at least with the sprayer hose and sometimes with the hot and cold valves.Seat the faucet in place, making sure that the gasket is lined up right, and then crawl under the sink and screw on the mounting nuts to keep the faucet in place. Tighten these first with your fingers, then with your basin wrench.Connection Odds and EndsUse your basin wrench to attach any connections you weren't able to get to above the sink, such as the shutoff valves, and double check to make sure all connections are as tight as possible. Turn the water back on either from your roof or from under your sink, and check on your new faucet to make sure that everything is running smoothly and there are no leaks. Turn on both hot and cold valves and try out any additional features that may have come with the new faucet. Make sure you are completely satisfied before putting away your tools.


How do you turn off the water to the outdoor faucet if the know turns and turns but does not get tight?

If it just turns and does not shut off the threads are striped on the end of the stem the handle is on. There is enough variance in faucets both in style and age that finding a new stem is unlikely. Time for a new faucet.