answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2006-07-16 10:55:47

everyone should have a manual for their vehicle, and the library should have a professional shop manual available in the REFERENCE section...make copies of the right sections...good luck :)

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


The horn on a Pontiac Transport is located in the engine compartment on the passenger side of the vehicle. It should be right behind the passenger side front headlight.


The low side ac port on a 98 Pontiac Transport should be on the side of the drier. The drier should be mounted on the passenger side near the radiator.



The 1997 Pontiac Transport 3400 rocker arm torque specifications are 18 pounds. The rocker arm should be torqued in six pound intervals.


You can find a wiring diagram that shows you how to hook up a trailer wiring harness on a 1998 Pontiac Transport at most auto parts stores. A Pontiac repair manual should have the diagram in it.


Should be under the glove blox. There a fuse panel there too! You should see the Falsher.(Silver Round).


Follow the main radiator hose located by the overflow tank. It should be where this hose attaches to the engine.


there is no timing belt on these vehicles! only one chain, and there(supposed) to LAST.


if the vin codes match then they should but i'd look at the wiring diagrams to be sure...


This is fun, get under the van on the drivers side appx. back to where the second row of seats are. There is a junction box where the fuel pump harness runs through. These often get corrosion and need to be cleaned up and that should do it!


Look in the glove box. There is a separate door in the glove box whtch should be very easily opened.


manifold gaskets only need to be replace if they leak, or if the manifold has been removed for some reason


should be a simple in and out procedure, but everyone should have a manual for their vehicle, and a professional shop manual should be available at the library in the reference section--you can make copies of the necessary information...good luck :)


The trans filter is located inside the trans. You have to remove the pan from the bottom of the trans. You should be able to see it when the pan has been removed.


when should the vapor canister be replace on a 1996 pontiac sunfire


When I bought my 1998 Pontiac it came with a kit that had the hoses. On left side of van by the lift gate is a panel cover. Take it off & insert the hose. The compressor should work. At least that's how mine works.


Remove the center nut, often you'll need to use an impact wrench so plan on getting other stuff out of the way. Borrow, rent or buy a wheel puller. There should be a couple threaded holes in the dampener pulley for you to connect the puller. The puller should easily remove the dampener pulley for you. Good luck.


You need to buy a puller ,one for the drive clutch [ on the motor ] and one for the driven clutch .That drives the ATV ! I bought mine from Dennis kirk for 60.00. Take the bolts out of center & put the puller in & tighten puller, they should come off


After removing the pinion nut, a 2 jaw puller should do the trick.


you should use a tool called a harmonic balance puller. the balancer came off in two pieces and the second piece that's still on the crank shaft won't come off


It should be perfectly safe for you to transport a drying machine on its side. It might not be safe for the drying machine. That is why you should follow the manufacturers recommendations. Your first priority is to make it safe for yourself. Your second priority is to have the machine in working order when you finish transporting it.


the torque converter clutch soelinoid needs to be replaced.your computer should have a trouble code.(tcc.error-###) it is labor intensive repair and should be serviced by seasoned mechanic.


It is located inside the frame that contains the wiper motor and reduction gear. You should take the whole wiper system off in order to get an access to the board.


There's a solinoid in the transmission.Suggest to check that first. Turn on interior lights. Start engine. If the lights go out when the engine stalls, you have a bad ignition switch.


Remove the big center bolt that holds the harmonic balancer in place. If you have a complete hub puller assembly, it should screw into threaded holes. You'll need to work something out to protect the crankshaft threads when you tighten down the puller, just be aware that you don't want to destroy the crankshaft by messing up the threads. Tighten the puller and it should remove the harmonic balancer for you.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.