answersLogoWhite

0


Best Answer
Copy

Standing in the front of your car facing the engine, in the middle of the valve cover on the left side (covered by black plastic). Remove that black plastic cover and you will see the PVC valve on the left side of the valve cover.

User Avatar

Wiki User

โˆ™ 2005-09-28 22:23:52
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: Does the 96 Tracker have a PVC Valve If so where is it located?
Write your answer...
Submit

Related Questions

How many valves does a 96 Geo Tracker 4 x 4 95 HP have?

Likely it's a 16 valve. When the Tracker first came out it was 8 valve, but sometime in the early 90s it went up to 16.


Where is the EVAP Vent Solenoid Control Circuit located on a 96 camaro?

Where is the evap purge control valve located on a 96 camaro


Will the seats from a 99 tracker fit in a 96?

The seats from a 99 tracker will not fit in a 96 because they are bigger.


How can you tell if a 1994 Geo Tracker is an eight or 16 valve?

16 valve engine not put in a Tracker till 1996. 1994 Tracker is 8 valve (but a Sidekick may have the 16 valve in 1994) Actually there were 16 valve Trackers before 96. I have an early 95 which is 16v version. I believe 16v engines started somewhere between 91-94. I do know that the valve covers usually state 16 valve when it is. ,the spark plugs in a 16 valve are waaayy down in the top of the engine,you need about a eight inch extention to get at them


Is the tps on a 93 tracker the same as the tps on 96 tracker?

No, 89-95 are the same, the 96 and later are different.


Where is the idle air control valve located on a 96 mustang?

under the hood!


Location of fuel pump relay on a 96 Geo Tracker?

The fuel pump relay on a 96 Geo Tracker is located in the main fuse box. It is positioned along the right side of the engine compartment, inside a water tight enclosure.


96 cavalier PCV valve location?

The PCV valve is located on the right side of the valve cover. After removing the hose, there is a retainer clip then the valve can be removed with pliers.


Will a 92 trans fit a 98 tracker?

No it will not 96-96 are compatible


Where is the PCV valve located on a 2006 Mitsubishi Galant 2.4L?

on my 96 2.4 its right on the valve cover,has a hose going to the intake manifold


Where is the egr valve located on a 96 sc2 Saturn?

Looking down on the engine, the EGR valve is to the right of the rocker cover, connected to the head.


Where is the PCV valve located on 96 ford ranger 4.0?

It's on the top of the drivers side valve cover towards the firewall end


Where is the PCV Valve located on a 1996 Ford Expedition?

I don't know about the 96', but for the 98' and 2000 it is located on the top of the valve cover on the passenger side near the back. Just pull the hose out and replace the valve on the end. .


Where is Fuel pump location 96 geo tracker?

Hi, Your fuel pump is located inside the gas tank. Steve H.


Is a 99 Chevrolet tracker brake caliper bracket interchangeable with a 96 Chevrolet tracker?

no the caliber are different.....


Does a 5speed 1996 Geo Tracker have power steering?

Yes it does. I have a 96 geo tracker and it does have power steering.


Where is the pcv valve located on a 96 223l xlt ford ranger?

its under the intake towards the front of the motor


How do you change the clutch cable on a 96 Geo Tracker?

hjfdjdfjgjdf


Will a 89 Geo Tracker interchange with a 96 Geo Tracker?

give noun for object. question is 100% no good. sorry.


What valve is exhaust and what valve is intake on 96 GM 350Ci?

The bigger valve is the intake.


Where is the cam shaft sensor in a 96 escort?

take the valve cover off and it should be located toward the rear of the engine write across from numder 4 intake valve


What is tcc circuit on 96 Geo Tracker?

torque converter control


How much freon will a 96 Geo Tracker hold?

21 ozs.


How do you make the OBD system in a 96 Geo tracker ready?

Drive it


How do you change the idle air control valve on a '96 Toyota Corrolla or '96 Geo Prizm?

It is located somewhere on throttle body, just unbolt and bolt new on on