answersLogoWhite

0

  • Head Gaskets and Valve Covers
  • Chevy Suburban
  • Chevy S-10
  • Air Filters and Intake Manifolds

Does the intake manifold and distributor have to be removed when changing the head gasket on a 1990 Chevy Suburban 350CI?


Top Answer
User Avatar
Wiki User
Answered 2006-08-02 21:16:16

Yes.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

In order to remove the intake manifold on a 1999 Chevrolet Suburban 5.7 do you have to loosen or remove the distributor?

Yes you do. The distributor must be removed.


How do you replace the gaskets on intake manifold for 2002 suburban?

To replace the Suburban manifold gaskets, unhook everything on the manifold, from fuel lines to vacuum hoses. The manifold needs to be unbolted then removed. Clean the old gasket material, then install with a new gasket. Make sure to use factory specs when torqueing down the bolts.


Where is the fuel pressure regulator on a 1999 Chevy Suburban located?

fuel pressure regulator 99 suburbanI have a 99 suburban 2500 with a 7.4 motor. In it the fuel pressure regulator is just below the distributor to the right. I had to remove the upper manifold and pull the distrbutor to change it. Wasn't as tough a job as it sounds, just took a while. Hope this helps. On a 99 Chevy suburban k1500 5.7L, the regulator is directly under the intake manifold. It is connected to the passenger end of the SCPI fuel injector assembly. You can't see it until you remove the manifold. It is held on by a clip that can easily be removed with a flat-head screwdriver. If you remove the regulator, take note of which direction the clip is facing because it will only go back on one way.


Where is the fuel pressure regulator located on a 1996 Chevy Suburban?

behind air intake manifold is the junction of the fuel injectors , it sits on the left side of that junction box if looking from front of engine. Unfortunately the air intake manifold must be removed to get to it .


How do you adjust timing on a 99 Chevy 5.7 liter suburban?

That requires an OBDII engine scanner to do that. The ignition timing is controlled by the computor. If you have not moved are removed the distributor then there's no reason to fool with the timing.


How do you change a starter on a 1995 Lexus SC300?

my understanding is plenum needs to be removed, and exhaust manifold to acsess the starter, mine clicks sometimes and needs changing also...


How do you change starter on 1996 sedan deville?

Changing the starter on a 1996 DeVille sedan can be a little complicated for beginners. The intake manifold will need to be taken off the car before the starter can be removed. After the manifold is removed, the starter can be taken off. The wires will need to be taken off the existing starter and labeled or taped for the new starter. The start is held in place by two bolts and after the bolts are removed the old starter can be removed.


Where is starter location on Toyota sequoia?

Under the intake manifold Between the top intake manifold and the engine block. The top intake manifold must be removed to access the starter.


How do you remove the spare tire on Chevy Suburban?

Removing a spare tire is easy to do from a Chevy Suburban. The tire is removed with the tool that is located on with your jack.


When you replace a 2004 Toyota Corolla starter does the intake manifold have to be removed?

when i change the starter corlla ce 2003 I take out a manifold


Where is the knock sensor for 1993 Toyota t100?

Under the intake manifold, right in the middle of the valley, on the block. The intake manifold has to be removed.


How do you change an S10 exhaust manifold?

The exhaust manifold on a Chevy S10 truck is changed by removing the spark plugs, unbolting the manifold from the cylinder heads, and unbolting the collector. The manifold can then be removed from the vehicle and a new set put in its place.


How do you remove the intake manifold on an eclipse?

To remove the intake manifold on the eclipse it is important to firstly remove the air intake, breather hose and the sensor at the top of the manifold. The battery should also be removed to remove the intake manifold on an eclipse.


How do youm replace the fly wheel on a 1988 Chevy Suburban with 5.7 liter engine?

The transmission has to be removed. Once the trnsmission is removed the fly-wheel is right there to be removed.


How do you get the head gasket off a 1996 buick regal?

The intake manifold, head, and exhaust manifold must be removed to gain access to the gasket.


How do you repair a blown head gasket?

The intake manifold and exhaust manifold must be removed. Then the head must be removed and the gasket replaced. The head must be checked for cracks and to see if it is warped. Then it is all put back together.


How do you install a distributor in a 1996 Yukon?

I removed the distributor in my 96 gmc yukon but I forgot to mark it before removing it.What do I need to do to get it back in.


Where is the transmission filter in a 1989 suburban?

Inside the transmission. Pan must be removed to access.


How do you remove fuel pump in 1999 suburban?

Located in fuel tank Probably have to be removed


Do you have to removed the distributor off engine to change pick up coil?

Usually, NO.


Does the magnet on the distributor shaft slide off?

The distributor will need to be removed. The magnet is permanently attached to the distributor shaft and the shaft is held in place by a roll-pin thatpasses through the distributor drive gear on the bottom side of the distributor. Magnet on top, gear down in the engine, distributor shaft and housing in the middle.


How do you remove a Sunfire distributor cap?

A Sunfire distributor cap can be removed with some simple tools. One way is to use a standard wrench and a towel.


How do you set distributor timing on a 2001 mercury villager?

Timing is set by the PCM and is not adjustable. The distributor should always be reinstalled in the same position it was removed from.


Where is located the knock sensor on a Nissan Xterra 2001?

if it is a v6 engine it is located underneath the intake manifold and you have to removed the manifold to replace it. if it is a 4 cylinder it is located on the back side of the engine block below the manifold


Where is the starter located on a 2004 Toyota Corolla?

We know were the starter is, how do you get it out? Does the intake manifold have to be removed?