answersLogoWhite

0


Best Answer
Copy

no it;s behind the harmonic balancer take off passenger right front tire and you can get at it. you will need a wheel puller to pull the harmonic balancer off

User Avatar

Wiki User

โˆ™ 2008-07-16 16:57:32
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Does the intake manifold on a 1999 Buick Century have to be removed in order to replace the cam shaft position sensor?
Write your answer...
Submit

Related Questions

Does the intake manifold on a 1997 buick century have to be removed in order to replace the camshaft position senson?

No it does not. Go to a parts store and buy a Haynes Manual that is specific to your car.


When should you replace your manafold gaskits on a 97 Pontiac transport?

manifold gaskets only need to be replace if they leak, or if the manifold has been removed for some reason


When you replace a 2004 Toyota Corolla starter does the intake manifold have to be removed?

when i change the starter corlla ce 2003 I take out a manifold


Where is the EGR valve on a 2002 2.3L Ford Ranger Does the intake manifold have to be removed to replace it?

no its out side of the intake


Where is the head gasket located on a 1999 Oldsmobile?

There are 2 of them. They are sandwiched between the heads and the engine block. In order to replace them the intake manifold and heads must be removed and exhaust manifold disconnected. Always replace both of them on a V6.


When fixing a blown head gasket do you have to replace the manifold gasket on a 1991 Nissan pickup truck?

If it was removed then YES.


Where is located the knock sensor on a Nissan Xterra 2001?

if it is a v6 engine it is located underneath the intake manifold and you have to removed the manifold to replace it. if it is a 4 cylinder it is located on the back side of the engine block below the manifold


How do you replace the gaskets on intake manifold for 2002 suburban?

To replace the Suburban manifold gaskets, unhook everything on the manifold, from fuel lines to vacuum hoses. The manifold needs to be unbolted then removed. Clean the old gasket material, then install with a new gasket. Make sure to use factory specs when torqueing down the bolts.


What is the cost to replace intake manifold gasket on 1996 Buick century?

I just had the intake manifold gasket replaced on my 96 century yesterday and my bill was $450 but my gasket was only leaking out. If its leaking into your oil it may be more.


How do you replace an egr valve on a 1998 Buick Century?

depends which one. the one in the cat is simple, unthread it and replace. the other in the manifold, not so easy.


How do you replace intake manifold gasket on Chevy pick up?

Remove everything on top of the intake (hoses, fuel rails, linkages.) Unbolt the manifold and remove it. Clean the old gasket off and replace it. Reinstall all parts removed to get to the gasket.


When to replace a manifold line and accumulator?

There is no set millage for when you should replace a manifold line and accumulator. Most mechanics only replace when the accumulator and/or manifold lineÊstart to fail.


Does the head have to be removed to replace lifters in a 4.0 liter jeep engine?

i dont think they do, the lifters are right under the intake manifold


What is the cost to replace the intake manifold?

what is the cost to replace a 2001 v-8 manifold intake


How do you replace a head gasket on a 95 sunfire Gt 2.3 L?

Remove the upper radiator hose, carburetor, intake manifold, and exhaust manifold. There are lots of hoses and wires going to various devices on the intake manifold and around the engine that have to be removed also. Additionally the alternator, water pump, smog pump, etc. need to be removed.


How do you replace fuel injectors in a1993 mercury villager?

The upper intake manifold must be removed for access, as well as other components. Once that is done, the fuel rail can be unbolted and the injectors removed.


How do you replace the valve cover gaskets on a 2003 Jeep Liberty?

To replace the valve cover gaskets on a 2003 Jeep Liberty, the valve cover is removed. The old gasket is then removed from both the valve cover and the manifold (old gasket will come off in pieces on both sides). Then spread the sealant on the manifold, place the new gasket on, then put sealant on top of the gasket and replace the valve cover and bolt down.


How do you replace cylinder head gasket on on 1993 Chevy Cavalier?

The intake manifold, exhaust manifold, and head must be removed. This is a major repair that should only be done by someone with the knowledge and skill to perform it correctly.


How do you replace a head gasket on a 1995 altima?

Intake & exhaust manifold must be removed. Then the head must be removed. head inspected for cracks or warping, and new head gasket installed. Not a repair for a novice.


How do you replace head gasket on 2003 BMW 745li?

The intake & exhaust manifold must be removed and then the heads. Major job that should only be attempted by a professional.


How do you replace the thermostat in a 1992 Buick century?

my dad and me took off the manifold and air intake off to get to it. and it didn't take more than a hour


Does the cab on a 2005 f250 6.0 have to come off to replace a manifold gasket?

No. which manifold gasket are you wanting to replace? Intake or exhaust?


How do you replace lifters in a 302 ford?

The valve covers and rocker arms need to be removed as well as the intake manifold. Then remove the push rods to gain access to the lifters.


How do you replace exhaust manifold gasket on 1986 K10?

unbolt the head pipe then the manifold.


Why should you have to replace your exhaust manifold gasket?

You have to replace the gasket because when you take the manifold off it brakes the seel and air will be sucked into the manifold and your vehicle will hardly run, and you wont be able to drive it You have to replace the gasket because when you take the manifold off it brakes the seel and air will be sucked into the manifold and your vehicle will hardly run, and you wont be able to drive it