answersLogoWhite

0


Best Answer

Incorrect torque pounds, or incorrect sequence of torque,improper gasket installation, foreign matter not allow gasket to properly seal or warped intake manifold or warped block

User Avatar

Wiki User

โˆ™ 2010-05-17 01:50:18
This answer is:
User Avatar
Study guides

cool

โžก๏ธ
See all cards
2.67
โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…
3 Reviews

Add your answer:

Earn +20 pts
Q: How can coolant leak from the front and rear exhaust manifold bolts after a overhaul?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you install an exhaust manifold on a Renault?

The exhaust manifold needs to have a gasket in place to help seal the juncture between the manifold and the engine. After the gasket and gasket sealer are in place, tighten the bolts for the exhaust manifold. The exhaust pipe can then be replaced on the new exhaust manifold.


How do you remove the Trailblazer exhaust manifold bolts?

I D K


What are the torque specs for head bolts on a 1992 Chevrolet 5.7L?

Cylinder Head bolts 65 ft/lbs=Intake Manifold bolts 30 ft/lbs==Exhaust Manifold bolts 25 ft/lbs=


How do you replace the intake manifold gasket on a 87 d100 slant 6?

remove the intake and exhaust manifolds. there are bolts that attach them onto the head and there are bolts near the carburetor that attach the intake manifold to the exhaust manifold.


How do you remove a intake manifold?

The exhaust intake manifold is held in place with 10 retaining bolts. Remove the retaining bolts and the intake manifold will come off.


How do you change the exhaust manifold gasket on a 93 Chevy astro van?

You will need to remove the exhaust manifold retaining bolts in your 1993 Chevy Astro. Remove the exhaust manifold. Remove the exhaust manifold gasket and clean the surface. Reverse the process to install the new exhaust manifold gasket.


Where is the coolant temperature sensor located in a 1998 Buick Regal GS?

It is located on the front side of the engine on the transmission side. It screws in right behind the front exhaust manifold where the manifold bolts to the crossover pipe.


What is the torque spec for the exhaust manifold on a 95 Honda Odyssey?

The 1995 Honda Odyssey exhaust manifold bolt torque specification is 45 pounds. The exhaust manifold bolts should be torqued in 15 pound intervals.


What are the torque specs for the exhaust manifold bolts on a 1976 corvette?

45 ft.lbs.


Do you have to remove the intake manifold to get to the exhaust manifold on 4.0 Jeep Wrangler?

Yes, they share the same gasket and bolts.


How do you change intake manifold gasket on a 1999 Olds Alero?

Remove the exhaust pipe from the exhaust manifold. Remove the manifold bolts. Remove the manifold. Remove the manifold gasket and clean the surface. Reverse the process to install the new manifold gasket.


1996 Nissan Pathfinder change exhaust manifold?

What engine???????? You should refer to repair manual if not familiar with auto repair and understand the terminology before attempting Remove nuts holding exhaust manifold to cylinder head & remove nuts/bolts holding exhaust manifold to exhaust pipes Use new exhaust manifold gaskets and install the new manifold securing the manifold to cylinder head (may need to but new nuts and or bolts) by "snugly" tightening manifold to cylinder head if not refering to repair manual

People also asked