0
How can you find the injector sleeve remover for the Isuzu MU for engine 30D cooler?
Wiki User
∙ 11y ago
Dear Sirs.
We are owner of on Isuzu MU with Chasi No. UES73EW4103619 and engine 30D Cooler.
We are looking for the INJECTOR SLEEVE REMOVER tool.
Because we look to the market and we did not found this tools we shall be much obliged if you can suply to us this tool.
Regards,
Costakis Pantelides
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Why are there long sleeve and short sleeve shirts?
Long sleeve shirts are smarter. Short sleeve shirts are cooler in summer.
Would a bad o2 sensor make the engine misfire and throw a p0303 code?
TSB 1803103 - 4.0L ROUGH ENGINE IDLE AFTER RESTART FOLLOWING A HOT SOAK Date: 09/05/03 (supercedes 1802702 dated 09/06/02) Model Year(s): 1999-2004 Description: NOTE: This bulletin applies to vehicles equipped with a 4.0L engine. This bulletin involves the installation of a fuel injector insulator sleeve. Details: Customers may describe a 20 to 30 second rough idle following the restart of a heat soaked engine. This condition may be most noticeable when the engine is restarted following a prior 10 to 20 minute heat soak in hot ambient conditions of approximately 32 C (90ºF) or higher. This condition may be consistent with short city stop-and-go driving trips and can be aggravated by the use of fuel with a high ethanol content. Depending upon various conditions a MIL may occur due to DTC P0303 - Cylinder #3 Misfire. This condition may be caused by heat from the exhaust manifold that following engine shut down migrates to the area around injector #3 and causes fuel vapor to form within the injector. This in turn may cause a momentary misfire of cylinder #3 until the fuel vapor is cleared of injector #3. The insulator sleeve lowers the injector #3 temperature to a point below which the fuel will not normally vaporize. If vehicle exhibits a rough idle, and if a misfire of cylinder #3 is observed following a 10 to 20 minute hot soak, perform the Repair Procedure. Parts required: 56028371AA Ignition Wire Shield Repair procedure: 1. Cut insulator sleeve, p/n 56028371AA, to make two (2) insulator sleeves about 25-30 mm (1 in.) in length. See diagram. 2. Install one sleeve around injector #3, with the slit on the upward facing side of the injector. Install the other sleeve with the slit on the downward facing side of the injector. 3. Confirm sleeve is flush to intake manifold surface around injector. 4. Check injector #3 wire and ensure that the injector is rotated to a 2 o'clock position. TSB for the cold start rough idle and P0303 code: TSB 18-010-01
What would you use to remove a paint mark from your sleeve?
If it's permanent you're screwed. If it isn't, any stain remover works well.
Why did the sleeve valve engine disapere from car engines?
To increase compression. Sleeve valves take a lot of combustion chamber space.
What is the difference between a wet sleeve and a dry sleeve in a diesel engine?
Dry sleeve is pressed fit into a cylinder and it does not contact with water.It is very thin. Whereas, wet sleeve is pressed fit into a cylinder and it contacts with water jacket.It is very thicker.
What causes coolant in oil of a series 60 dietroit diesel?
Let's see...cracked head, cracked head gasket, cracked intake gasket, bad cylinder liner or cracked block, air compressor head gasket...if this was a Cat 3116 I'd also look at the oil cooler or an injector sleeve, but it's not so that's probably not it.
Should i put a sleeve in a cracked engine block that's into a water jacket?
depends on what your using engine for but no i would not recommend it
What are the two parts of a celinder in the car engine?
Presuming that you mean "cylinder", the two parts are the bore and sleeve.
What is a pagoda sleeve?
A pagoda sleeve is a funnel-shaped sleeve arranged to show the sleeve lining and an inner sleeve.
How do you remove an engine sleeve?
I have made a couple different sleeve pullers an it depends on what typeof sleeve you are trying pull if it is a wet sleeve like for a cat engine where the sleeve rides below the block the best way to make one is out of 1/2" flat steel an cut it out in a "T" shape an turn the "T" upside down an make it so the cross on the Tprotrudes out of the sleeve by at least 1/8" an drill a hole in the top of the leg so you can put a clevis in it. Then put a short piece of chain on. an weld a bolt to the other end an bridge over the top on the block an tighten the bolt an it should pull up the sleeve An if it bends the "T" you might have make it more of a triangle shape An if it is a dry sleeve like in a old tractor you will need cut one out in a circle that will just go inside the block an catch the sleeve drill a hole in the middle of the plate an use the chain an bolt good luck
What are the basic types of sleeves in garment making?
THE THREE BASIC TYPES OF SLEEVES ARE : KIMONO SLEEVE RAGLAN SLEEVE SET- IN SLEEVE THE THREE BASIC TYPES OF SLEEVES ARE : KIMONO SLEEVE RAGLAN SLEEVE SET- IN SLEEVE THE THREE BASIC TYPES OF SLEEVES ARE : KIMONO SLEEVE RAGLAN SLEEVE SET- IN SLEEVE
What are the Types of sleeve?
The types of sleeves are: no sleeves,spaghetti strap (thin or thick), short sleeves,3/4 sleeves, and long sleeves.there is also bishop sleeve, lantern sleeve, shirred sleeve, bat-wing sleeve, saddle sleeve, french sleeve
