answersLogoWhite

0


Best Answer
Copy

The best way to do this is to cut the plastic on the cable housing and then you can pull it with a pair of pliers. If its just the handle broken off the cable inside the car you can pull it there without any problems otherwise you are going to have to find a place to cut it you can reach without to much problem.

To release that go under your car in the front and reach up and locate the cable if there is one and follow it to the end there is a lever that you need to pull toward the drivers door if there is no cable then find that same lever by touch in the middle of your hood you will know what it feels like byits design it should feel like a small extended metal lever

2015-07-15 21:35:25
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you get the hood up on a Buick LeSabre when it will not release to the safety catch?

That depends on a few things. If the cable has broken at the release handle, you can use Vice Grips or pliers to grab the end of the cable and pull. If the hood is stuck down you can have a helper pull up on the hood while you work the release in the car. If the cable has broken at the latch consult a pro for help. If you get a helper to hold the the hood release open on the inside and tap lightly, with the side of your fist, on the front of your hood just above the grill. This will usually work if the cable is not broken.


How do you fix the power window cable on a 2000 Buick Lesabre?

im not so sure


How do you open the hood on a 97 buick lesabre when the latch is broken?

The best way to to try to find the cable and cut it and pull with pliers to open if the inside latch is broken. If not then you would have to go in from underneath or through the grill.


How do you replace the positive battery cable on a 1997 Buick LeSabre?

Disconnect the cable from the LeSabre battery. Follow the route of the cable and disconnect the other end. Pull the cable out, then fit the new cable in the same direction. Connect the non battery end, then connect to the battery.


How do you open your hood when the inside release is broken on a 1995 Buick Century Special?

Use pliers and pull the cable...


Where is the location of the 1998 Buick Lesabre neutral safety switch?

Under the shifter cable on top of transmission.


Where do you connect the negative cable when jump starting a 2002 buick lesabre custom?

Ground on the engine block.


How do you change the antenna cable on a 1998 buick lesabre limited?

To change the antenna cable on a 1998 Buick LeSabre Limited, a person has to unscrew the old antenna cable from the back of the radio. Then pull the antenna wire out from under the dash and follow it to the antenna. Unscrew the old cable from the antenna. Screw in the new cable and thread it back under the dash in the same path as the old cable and screw it to the back of the radio.


Where is the starter located on a 1990 buick lesabre?

Hey, every starter is located at the end of the hot cable from your battery. ( the cable marked red on the battery or with the + sign.


How to replace Alternator on 97 buick lesabre?

Remove the positive cable from your 1997 Buick LeSabre battery. Remove the alternator belt. Remove the alternator wiring harness. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


Where is the starter on a 1993 Buick lesabre with a 3.8 engine?

By the flywheel flexplate bottom of engine, follow batt cable (pos) to the end.


Where do you connect the negative cable when jump starting a 2001 Buick LeSabre?

Somewhere on the engine. Just find a good point that is away from the belts.


Where are ground wires on 1994 buick lesabre?

There are many ground wires on this vehicle. The main one being the negative, (Black) battery cable.


How to manually release hood on buick regal that the interior switch has been broken?

it is next to drivers side on floor in front, take pliers and pull up on cable, this will release hood latch


Broken hood release cable on 1990 Buick Century how do you get the hood open?

You can take the front grill off, with some T20 screws on the front of the car. You will see the hood release cable, and the mechanism that it attaches to. Just look at it, and you will be able to figure out how to open it from there.


Where is the computer module located buick lesabre 1997?

front left fender under black cover,make sure to unhook battery cable first.


How do you open the hood on a 94 Buick Roadmaster with the latch cable broken?

Remove the grill, cut the cable and pull it with a pair of pliers or vice grips. It might even be possible to push the release on the latch manually, after the grill is removed.


How to reset computer codes on 2003 buick lesabre?

Take the negative battery cable off, then turn the ignition to the on position to leave the ignition on for 5 seconds then turn off. Then reconnect your negative battery cable.


How do you fix the cable for the hatch release on a 92 Blazer S10?

It depends on where its broke at. Is the cable broken at the mechanical part or is it broken before that?


How do you open the hood on a 1992 Buick Century when the hood latch is broken?

Use a set of pliers to pull the cable even if the plastic latch is broken...


How do you open hood release cable on 1993 Buick roadmaster?

Remove the grill


Broken hood release cable town and country?

Hood release cable has connector nuts on both ends of the cable. Loosen the connector nuts. Remove the cable retainers. The cable will come off and can be replaced with a new hood release cable.


How do you open trunk when cable release is broken?

With a key or from the inside.


My 1991 Buick lesabre motor dies out on right hand turns at 30 to40 mph but not on left hand turns?

I had the same problem. I took my Buick to a dealer. I told them it was possibly a bad battery cable. They did not listen. They did unnecessary work which total about $600.00 dollars. It was the battery cable - about $30.00 total.


How to remove radio 1996 buick lesabre?

Remove the decorative radio retaining plate. Remove the retaining screws. Pull the radio out. Remove the wiring harness. Remove the antenna cable.