I am kind of leery on anwsering this question, because if you aren't sure how to pull the tranz, I don't think that there is any reason that you need to be inside of it, but here it goes. I belive the you should be able to get enough clearance by removing the drivers side frame rail, and tilting the engine/tranz combo. Drain the tranz, pull the left axle, and pull the side cover. There you will be looking at the valve body. Pull the pump, shaft, harrness, and pressure switch assy. Then come the valve body and seperator plate. (Watch for falling checkballs) Dissconnect the manual valve, and unbolt the Channel Plate. When removing the channel plate the three accumutlator springs may fall out. If they dont remove the springs. You will need a 2 jaw puller to remove the output shaft sleeve. After removing the sleeve, pull the driven and drive gears out, and any pieces of chain that you might seeMake sure every thing turns freely and doesn't have excessive play, and make sure nothing got too hurt from the chain breaking, install new chain and gears, new output shaft sleeve, and reassemble. Drop oil pan, install new filter, flush cooler, refill with oil, and give it your best blessings. I would however recommend an overhaul, but the choice it yours.
It is a involved procedure , if you have to ask then you shouldn't be doing that. the whole frame in the front has to come out.
Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
You have to remove the transmission to replace the torque converter.You have to remove the transmission to replace the torque converter.
Remove the inside door panel of your 1993 Chevrolet Lumina. Remove the passenger mirror wiring harness. Remove the passenger mirror retaining bolts. Reverse the process to install the new passenger mirror.
Between the engine and transmission inside the bellhousing, you need to remove the transmission from the engine to see/replace it.
If you remove the transmission pan, it is the part bolted to the inside of the transmission.If you remove the transmission pan, it is the part bolted to the inside of the transmission.
Remove the inside door panel of your 1994 Chevy Lumina. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
It is inside the transmission, remove the pan on the bottom to access.It is inside the transmission, remove the pan on the bottom to access.
It depends on where the slave cylinder is located. If it is inside the bell housing you will have to remove the transmission.
remove bolts and replace it how do u think
Transmission filters are INSIDE the transmission. You need to remove the transmission oil pan. When you replace the filter, plan on replacing the pan gasket as well.
The modulator is located just above the starter on the side of the transmission, it has a vacuum hose attached to it. The solenoid is located in the transmission, you have to remove the transmission pan to remove it.
Have to remove the transmission.
To replace the slave cylinder on this vehicle you will have to remove the drive shaft and then the transmission. The slave cylinder will be bolted to the inside of the bellhousing. The transmission is very heavy so be very careful.
Remove the wiring harness from the and of your 1997 Chevy Lumina antenna. Remove the antenna retaining nuts. Reverse the process to install the new antenna.
Loosen the rear transmission mount retaining bolt. Jack the transmission up a couple of inches. Remove the retaining bolt and the transmission mount.
remove the 2 bolts andharness
need to replace transmission seals
To replace a turn signal switch in a 1993 Chevy Lumina go to the trunk of the vehicle and find the plastic covering for the turn signal. Remove the cover and replace the bulb.
remove gas tank.pump is inside
Automatic transmission oil filters ware located inside the transmission, under the transmission oil pan. You have to remove the transmission oil pan to replace it and then you will need to refill it with new transmission fluid.
Remove the inside door panel. Remove the window clips that hold the window onto the track. The window will come out. Reverse the process to install the new window.
To replace timing chain on a 3.1 Chevy Lumina engine, you need to first make sure that your motor or engine is turned off. Then you need to remove the chain and replace it.
Remove the fuel tank. Mounted inside on the top of the tank.
You must remove the transmission are engine to replace the rear main seal.