answersLogoWhite

0


Best Answer

Yes! Find the wires going to the washer switch and just use a toggle switch in it's place. If you can't locate the wires, you can just run power straight to the motor from the toggle switch. I recommend you use a spring loaded on/off toggle switch, to make sure you don't accidentally leave it in the on position.

User Avatar

Wiki User

โˆ™ 2006-03-15 23:51:30
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How can you rewire a washer fluid motor to just a toggle switch on an 88' Chevy Beretta?
Write your answer...
Submit
Related questions

2002pontiac grandprix the windshield washer won't work how to fix not a fuse?

had same problem washer pump worked fine i found that out by cuting wires and hooking direct to battery so the next step was for me to put in a 2 way toggle switch and find a place to mount it and now i use the toggle switch and it works fine so rewire worked for me you can fix it yourself and save big $


Where is the fuel pump relay switch in a 89 beretta?

It is on the Firewall beside the Washer Pump, it is behind the Fuel Fuse and a Bolt that has constant power to it.


Where is relay switch for washer motor on 2001 model Peugeot 406 estate?

The relay switch for the washer motor on a 2001 model Peugeot 406 Estate is located at the controls of the windshield washer. It is near the washer fuse.?æ


Where is washer relay 2007 Avalon?

The 2007 Toyota Avalon windshield washer relay switch can be found in the fuse box. The windshield washer relay switch will be in the third column, second from the top.


Ge washer wont spin or drain?

check the lid switch it is under the top of the washer and is usually activated by a pin attached to the lid of the washer


How do you replace the front washer switch on a 1993 Jeep Cherokee Sport?

I believe in the 93 the switch is built into the wiper arm. The actual switch is inside the steering column. The steering wheel must come off, and part of the colum itself. this is a difficult job. A much simpler way is to mount a new toggle switch inside the vehicle and run the wires back to the pump. Cut the existing wires and splice the new one in to activate the pump from the new switch.


What is the multifunction switch?

it's the turn signal,wiper,washer,cruise,and emergency switch all in one.


Where is neutral safety switch on 2002 ford ranger?

whats the washer used on a neutral safety switch


How do you test the lid switch on whirlpool washer?

how do you test and reset the lid switch on the top load models of whirlpool


2002 SSEI washer arm needs replacement how does it come out-off?

Sorry.. i meant washer switch on steering colum


Maytag washer fills with water but will not agatitate?

If a Maytag washer fills with water but does not agitate it could a problem with the switch in the lid. There is a switch that locks the lid down during agitation and spinning. The magnet could be defective.


Where is fuse for washer pump for 2003 Jeep liberty?

The owners manual list fuse number 22 as: Wiper Switch/Front & Rear Washer


What is a combination switch on a car?

A combination switch is the unit behind the steering wheel that hold the controls for the lights, cruise control and window washer.


How to fix lid switch on kitchen-aide washer?

If you are sure the lid safety switch is at fault do not bother with it, they are cheaper and easier to replace


How do you stop 2003 Chevy Express washer is always on it kills the battery?

Well, either you've got a short to power or a stuck switch. The simplest way to stop it for the moment is to unplug the wire from the windshield washer motor. To get it functioning the way it's supposed to again, you're going to have to diagnose it and repair it accordingly. I would start by disconnecting the stalk switch, isolating the circuit for the windshield washer pump, and seeing if you have continuity in that circuit with the switch released. If you do, the switch is stuck, and you're going to have to replace it.


What does it mean when the washer does not do anything or make any noise when the washer fluid mechanism on the washer handle is activited on a 2002 Ford F-250?

Don't know. Means a burned out fuse, bad switch or bad pump.


Replaced new washer pump and it still not working for a wrangler?

If a washer pump was replaced on a Jeep Wrangler and is still not working the fuses should be checked. The washer switch should also be checked as it could also be causing the pump not to work.


What has caused my brake lights to not work if it's not the fuse bulbs or switch?

Check the wiring to the switch they break at the connector to the switch tug on the wires a bit sometimes they break inside the wire covering.Or it could be a multifunction switch( the signal and washer high beem switch)


What are the buttons on the end of the light and wiper control sticks on a Mitsubishi shogun?

it is the switch for the headlight washer pump


Replace brake light switch on 2004 ford expedition xlt?

Brake Light Switch Removal & Installation 1. Lift the locking tab on the switch connector and disconnect the wiring. 2. Remove the hairpin retainer, slide the stop lamp switch, pushrod and nylon washer off the pedal. Remove the washer, then the switch by sliding it up or down. > On trucks equipped with speed control, the spacer washer is replaced by the dump valve adapter washer. 3. To install the switch, position it so that the U-shaped side is nearest the pedal and directly over/under the pin. 4. Slide the switch up or down, trapping the master cylinder pushrod and bushing between the switch side plates. 5. Push the switch and pushrod assembly firmly towards the brake pedal arm. Assemble the outside white plastic washer to the pin and install the hairpin retainer. *** CAUTION*** Don't substitute any other type of retainer. Use only the Ford specified hairpin retainer. 6. Assemble the connector on the switch. 7. Check stop lamp operation. *** CAUTION*** Make sure that the stop lamp switch wiring has sufficient travel during a full pedal stroke!


Brake lights don't work but blinkers and hazards do is it a fuse or brake switch?

Brake Light Switch 1. Lift the locking tab on the switch connector and disconnect the wiring. 2. Remove the hairpin retainer, slide the stop lamp switch, pushrod and nylon washer off of the pedal.Remove the washer, then the switch by sliding it up or down. (On trucks equipped with speed control, the spacer washer is replaced by the dump valve adapter washer.) 3. To install the switch, position it so that the U-shaped side is nearest the pedal and directly over/under the pin. 4. Slide the switch up or down, trapping the master cylinder pushrod and bushing between the switch side plates. 5. Push the switch and pushrod assembly firmly towards the brake pedal arm. Assemble the outside white plastic washer to the pin and install the hairpin retainer. (Caution: Don’t substitute any other type of retainer. Use only the Ford specified hairpin retainer.) 6. Assemble the connector on the switch. 7. Check stop lamp operation. (Caution; Make sure that the stop lamp switch wiring has sufficient travel during a full pedal stroke!)


How to Check the brake light switch on the brake pedal linkage?

Brake Light Switch Removal & Installation 1. Lift the locking tab on the switch connector and disconnect the wiring. 2. Remove the hairpin retainer, slide the stop lamp switch, pushrod and nylon washer off the pedal. Remove the washer, then the switch by sliding it up or down. > On trucks equipped with speed control, the spacer washer is replaced by the dump valve adapter washer. 3. To install the switch, position it so that the U-shaped side is nearest the pedal and directly over/under the pin. 4. Slide the switch up or down, trapping the master cylinder pushrod and bushing between the switch side plates. 5. Push the switch and pushrod assembly firmly towards the brake pedal arm. Assemble the outside white plastic washer to the pin and install the hairpin retainer. *** CAUTION*** Don't substitute any other type of retainer. Use only the Ford specified hairpin retainer. 6. Assemble the connector on the switch. 7. Check stop lamp operation. *** CAUTION*** Make sure that the stop lamp switch wiring has sufficient travel during a full pedal stroke!


Where is wiper switch headlights 2000 S80?

that switch does not exist. It simply is activated when you spray your windshield washer fluid onto the windshield. Your headlight switch has to be on. I know your lights are always on, however the wipers for your headlights will only activated if the headlight switch is in the on position.


Where is the brake light sensor in a 1989 F150?

Brake Light Switch Removal & Installation 1. Lift the locking tab on the switch connector and disconnect the wiring. 2. Remove the hairpin retainer, slide the stop lamp switch, pushrod and nylon washer off the pedal. Remove the washer, then the switch by sliding it up or down. > On trucks equipped with speed control, the spacer washer is replaced by the dump valve adapter washer. 3. To install the switch, position it so that the U-shaped side is nearest the pedal and directly over/under the pin. 4. Slide the switch up or down, trapping the master cylinder pushrod and bushing between the switch side plates. 5. Push the switch and pushrod assembly firmly towards the brake pedal arm. Assemble the outside white plastic washer to the pin and install the hairpin retainer. *** CAUTION*** Don't substitute any other type of retainer. Use only the Ford specified hairpin retainer. 6. Assemble the connector on the switch. 7. Check stop lamp operation. *** CAUTION*** Make sure that the stop lamp switch wiring has sufficient travel during a full pedal stroke!


Where can you buy a used or like new wiper washer switch for a 1994 Previa?

YOUR BEST BET IS A SALVAGE YARD