the front fender is really easy to replace. you first have to remove the two bolts holding the hood to the car, they will be on the body when you lift the hood up. you will then need to take the two or three screws out that you will find where the hood sits. after that remove the screws that hold it to the wheel well theres usually 4-6 screws. after those are out its pop and pull
How do you replace an 1994 3.1 Oldsmobile Achieva s radiator?
is it hard to change the water pump on a 1992 Oldsmobile achieva. Yes, it is very hard to replace a water pump on an Achieva. When the pump died on my 1996 Achieva, the engine needed to be unbolted and removed to get to it. As I recall, it cost about $500. I have a 95 Olds Achieva 3.1 and the water pump was very easy to change. Mine is on the front passenger side of the engine. Very easy to get to, just be careful not to break any bolts off. lol
To replace most heater cores you have to remove the dash on the passenger side.
replacing achieva serpentine on a 96i have a 96 and you have to completely remove the motor mount and all of the bolts holding it on the engine to replace the belt,also carefully jack up the engine since it will fall on the ground if you take off the mount
did u ever figure it out?
you need to replace your heater core.
It is located on the drivers side of the crankshaft pulley. The shop time to replace it is 1.4 hours and the part is about $80. It would be around $225 to have the dealer replace it.
Passenger side, near the firewall. It is not difficult to replace, it is just very difficult to get to.
Back by the fuel tank itself, look around and it is easy to get and replace
Changing brakes is a simple task. Lift the car, remove the wheel, remove the brake shoe, replace the pad, replace the shoe, replace the wheel and lower the car.
What about the sun visor...the answer didn't say anything about how to remove and replace the visor
How do you replace the front drivers seat on a 1996 Chevy S10 pick up truck
how do i replace the drivers side headlight in a 2003 oldsmobile silhoutte
how do i replace drivers side mirror Nissan maxima 2005
On my 1994 achieva its vacume controlled i had to replace the line going to the controller. It was broken. It runs frin the top of your intake throttle body its a small line maybe 1/8 inch down to a vacume tank in lower front drivers side, from there it runs up the drivers side fender accrossed the firewall towards the top and into the passanger side through the firewall. It comes though behind the glove box and over to a vacume spliter behind the vent selecter. mine broke right at the vacume spliter. Word of advise use heavy stiff plastic vacume line to replace it anything less will colapse when vacume is applied. this solved my problem. the line is very easy to replace.
replace cam shaft sensor,location behind main pulley
Unless there is an access panel inside the trunk, then the answer is yes. Sadly, yes. In my 1996 Achieva it cost me about $700 to drop the tank and replace the pump. I was ripped off, I know, but the tank needs to be removed to get to the pump.
1992 olds Achieva does not have that switch. ECM receive signal from the coolant temperature sensor and send command to relay #6 for turn on/off the radiator fan. Relay #6 is located in the motor compartment on the fireboard.
how do you replace the drivers window clips on the glass od a 1995 grand prix se 2 door?
Very difficult job. All of the hinges are welded in that's one problem. To correctly replace the drivers side upper half, the dash assembly needs to be removed to gain access to the back side of the "A" pillar. I would suggest purchasing a shop manual if you intend on doing that job yourself.
The starter is hard to get at under the fuel lines and junk on the drivers side of the engine compartment. I had mine done by a mechanic because it was to difficult for me to get at.
how do you replace the drivers side drive shaft and cv joint?
If I remember correctly, it was $12 to replace my drivers license when I lost it in 2012.
you call a profesional then rip it off and sew them
replace the drivers for the printer