Power Steering
Toyota 4Runner

How difficult is it to replace the power steering pump on a 1993 4 runner?

161718

Top Answer
User Avatar
Wiki User
2006-03-22 16:52:30
2006-03-22 16:52:30

not too difficult with the right tools. if you need to buy the tools to do the job, youll probably spend more than the labor to have a pro do it! Yeah, but then you'll have more tools!! ******Not too hard...just did mine...all you need is a low profile puller for the pulley if you dont want to remove the radiator.....1. Remove the battery. 2. Siphon the steering fluid out of the reservoir tank. 3. Disconnect the return hose from the pump. 4. Disconnect the pressure line at the pump by removing the union bolt. ( Remove 2 vaccum hose if with RWAL) 5. Loosen the drive belt pulley retaining nut. Loosen the idler pulley and adjusting bolt and remove the drive belt. 6. Remove the pulley and the woodruff key. (This is the sad part, depending on how tight the pulley is, you might end up denting the pulley so be ready to buy a new one. but you can reuse the woodruff key.) 7. Remove the power steering pump....Installation is in reverse.... then Bleed the system...... Note: 1. If your vehicle is equipped with RWAL, have the dealer bleed and check the system since they have the ABS checker. Without the RWAL you're good to go.... 2. New or Reman P/S Pump dont come with the vaccun valve, so remove the valve from the old pump and transfer it to the new one....

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

no, it just screws into the steering box and screws into the power steering pump, or it might use a hose clamp for the power steering pump, it just depends.

User Avatar

Check my submissions. I just answered it for someone.

User Avatar

Remove the plug on the bottom of the power steering fluid pump. Drain the power steering fluid out. Replace the plug to the bottom of the power steering pump. Replace the power steering fluid.

User Avatar

What have to do replace the belts water pump power steering

User Avatar

It can run between $200 and $300 for a person to replace a Toyota 4 runner power steering pump. It could be cheaper if a person gets the part at a junk yard and makes the change on their own.

User Avatar

It's not too difficult to find a leak if you can get the vehicle on a rack to look at it from underneath. And power steering hoses can be difficult to replace if you are not mechanically experienced and have the proper tools. Best to leave it to a mechanic.

User Avatar

How do you replace a power steering reservoir for a 2000 odlsmobile interigue?

User Avatar

How do you replace the power steering pump for a 1987 Toyota Supra?

User Avatar

how do you replace power steering hose on 99 chev venture

User Avatar

How to replace the power steering depends on which component you wish to replace. Let us know what it is and we will get back to you.

User Avatar

how do i replace a power steering pump in a 1990 toyota camry?

User Avatar

How to replace power steering hose in 1999 ford excort

User Avatar

How do you replace power steering belt on 2003 Mazda protege ?1.6

User Avatar

how to replace the power steering hose on a 2001 oldsmobile aurora 3.5 liter engine

User Avatar

If Your steering has gotten difficult it is likely that you need to add power steering fluid. If that is not it then your power steering pump might be going out.

User Avatar

it will be difficult to turn your steering wheel

User Avatar

http://www.carstereohelp.com/stereoremovalToy4Runr2PwrAnt.htm

User Avatar

You will need to remove the belt from your power steering pump. Remove the power steering hose. Remove the power steering retaining bolts. Reverse the process to install your new power steering pump.

User Avatar

Remove the power steering hoses from the power steering pump. Remove the power steering retaining bolts. Reverse the process to install your new power steering pump.

User Avatar

how to replace power steering pump on 1994 Mazda b2300

User Avatar

i have a leak in power steering lines on 99 Malibu . show me line schematics

User Avatar

To replace the power steering rack on a Saturn Ion, You must first dissmantle the current steering rack by accessing the main hood, and from there you can screw the new steering rack into place

User Avatar

Drain the fluid from the power steering pump. Remove the power steering hose. Remove the wiring harness from the power steering pump. Remove the power steering pump retaining bolts. Reverse the process to install the new power steering pump.

User Avatar

Loosen the tensioner pulley. The power steering belt will come loose. Remove the power steering belt. Reverse the process to install the new power steering belt.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.