Thermostats
Oldsmobile Ciera

How difficult is it to replace the thermostat on a 1990 Cutlass Ciera with a 3300 engine?

282930

Top Answer
User Avatar
Wiki User
2014-09-18 00:22:04
2014-09-18 00:22:04

It is quite easy to change the thermostat in your 1990 Cutlass. Remove the thermostat housing retaining bolts. Remove the thermostat from the housing. Reverse the process to install the new thermostat.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The thermostat is located where the hose leaves the engine to go to the top of the radiator. You unscrew the bolts holding the hose mounting to the engine. There you find the thermostat.

User Avatar

The 1993 Oldsmobile Cutlass Sierra thermostat is located on the front of the engine. You can follow the water supply line from the radiator to the thermostat housing.

User Avatar

The thermostat of a Vauxhall Zafira is located in front of the engine. The unit is on engine itself and has a main radiator hose connected to it. To replace it remove the hose and unbolt the house from the engine. Replace the thermostat in the housing.

User Avatar

For a 3.2L engine. It's located at the engine side of the bottom radiator hose. It is very difficult to replace, but not impossible. JF

User Avatar

To replace the thermostat on a 2002 Nissan Altima first drain out the coolant. Then proceed the to locate the thermostat housing which is by the engine compartment fuse box. Unbolt the housing and replace the thermostat.

User Avatar

Should be in a removable housing at the engine end of the upper radiator hose

User Avatar

If it is a 2.7L engine, then the thermostat is on the bottom side of the engine where the radiator hose flange is. It is a pain to do.

User Avatar

The hose that goes in the top of the engine, the thermostat is in the hose.Unscrew the hose take the thermostat out and replace,Very easy

User Avatar

follow the upper radiator hose from the radiator to the engine this is where youwill find the thermostat housing. remove ther housing and you'll be looking at the thermostat. it is realy easy

User Avatar

Some engines are easier than others. Follow the upper rad hose from the rad to the engine and there you will find the housing for the thermostat. take the 2 bolts holding it out after taking the hose off and when replacing it make sure the spring goes toward the engine.

User Avatar

Remove the top radiator hose. The thermostat is located under the hose inlet on the engine. Remove the inlet to replace the thermostat.

User Avatar

My 97 4.0 Ranger's thermostat is in the front of the engine. I has two bolts you have to take off. I had to replace the gasket. Leaked when I got on it hard. It's called the "thermostat housing. Thermostat is easy to replace. Great engine.

User Avatar

Look at the engine end of the upper radiator hose in a removable housing

User Avatar

Located in a removable housing at the engine end of the upper radiator hose

User Avatar

Follow the top radiator hose down to the water outlet on engine. The stat is in there.

User Avatar

Thermostat is inside a metal cylinder on the left side of the engine. Just undo the top. Removing it is difficult as it is a tight squeeze out. Installation takes less than 30 minutes.

User Avatar

Replace it with the exact same temperature thermostat as the one you removed. Do not run the engine without a thermostat. The thermostat is required to keep the engine running at the optimum temperature that will give the best performance and mileage. If it is overheating running it without a thermostat is not the solution.

User Avatar

thermostat is located on engine block. follow top water hose leading to engine. thermostat is located inside the water intake. remove hose. remove water intake(two bolts)housing. replace thermostat. .

User Avatar

Follow The TOP Radiator Hose From Radiator To The Engine. Where It Is Clamped On Remove The Hose. Behind The Housing Where You Removed The Hose Is The Thermostat

User Avatar

To replace a thermostat on a 1992 Geo Storm first locate the its housing. Once found drain the coolant system and remove the housing from the engine. Replace the thermostat.

User Avatar

The thermostat is located on the top of the engine, where the top radiator hose is connected. The hose has to be disconnected, and the inlet on the engine is removed, with the thermostat underneath.

User Avatar

The thermostat is located in the thermostat housing at the engine end of the top radiator hose.

User Avatar

follow top rad hose to engine the thermostat is in that housing


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.