Auto Parts and Repairs
Dashboard Lights and Gauges
Mercury Villager
Toyota Camry

How difficult would it be to replace the burnt out light bulbs in a 1996 Villager instrument panel?

323334

Top Answer
User Avatar
Wiki User
2015-07-15 20:55:42
2015-07-15 20:55:42

You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You have to remove the instrument cluster to get access to the bulbs.

User Avatar

The instrument cluster needs to be removed to get at the bulbs.

User Avatar

The instrument cluster must be removed to replace the light bulbs on it.

User Avatar

There are no individual bulbs, just LED's in the dials, and you will have to replace the entire instrument cluster.

User Avatar

Remove the instrument cluster then replace the bulbs. = =

User Avatar

To change the dash light bulbs you must remove the instrument panel.

User Avatar

You need to remove the dash in order to get back there to replace any blown bulbs.

User Avatar

You have to remove the instrument cluster to service the light bulbs.

User Avatar

It is very hard. You need to remove the entire dash to get to the bulbs. These are maybe not worth replacing unless more than one is out.

User Avatar

Remove the instrument cluster and replace the bad bulbs. Take the battery cables off!Remove the upper and lower steering colum covers. Remove the four screws on the cover. Tke the screws out of the cluster and turn it over. Replace the bad bulbs. Had to replace the whole cluster on mine as the speedometer and the heat guage were kaput!

User Avatar

How do you change the light bulbs in the instrument panel in 1998 Toyota corolla

User Avatar

there aretwo sizes for the bulb and bulb base small and large but you can replace just the bulb from the base socket. I recommend that you (url )instrument panel light bulbs or cluster panel light bulbs to find the two sizes that you will need. autolumination.com or autoanything.com or rockauto.com

User Avatar

You take out the cluster and replace the bulbs in the back of the cluster. Very simple job, takes baout 10 mins!

User Avatar

Replace the light bulbs that are burned out, usually from the back side of the instrument cluster.

User Avatar

-- Without changing the bulbs, increase the voltage of the battery or power supply. -- If the bulbs are in series, take one out of the circuit, and replace it with a piece of wire. -- Replace incandescent bulbs with others whose filaments have lower resistance. -- Replace incandescent bulbs with fluorescent tubes. -- Replace incandescent bulbs with LEDs.

User Avatar

Remove the 2 screws at the top of the instrument cluster bezel (or dress front cover), carefully pry out with a small screwdriver and set aside. Remove the 4 screws that hold the instrument cluster to the inner dash and pull out. Turn instrument cluster over to access the bulbs for removal and replacement. Twist the bulb retainer to remove.

User Avatar

Below the instrument cluster is a trim piece that goes across the width of the instrument cluster. Remove the 4 screws then remove the trim piece. Remove the screws that retain the instrument cluster, then carefully pull the instrument cluster STRAIGHT BACK. The instrument cluster plugs in to a matching socket in the dashboard. Be certain that the pins do not get bent. It's a good idea to replace all of the bulbs once one burns out. The rest will be failing soon. There are two types of bulbs used in the dashboard, they might only be available at a GM dealership. Replace all of the bulbs. Carefully push the instrument cluster back into the dashboard, then test the lights and make certain that the instruments and indicator lights work before putting everything else back together. Replace the trim ring around the instrument cluster. Replace the bottom trim piece... Done. ... at least, that's how it works on the 2000 LS

User Avatar

i would suggest that you go and buy a Haynes workshop manual from Halfords as it tells you what to do and has pictures that help, i have changed the bulbs on my vectra and without the book i would not have had any idea where to start.

User Avatar

http://www.sylvania.com/ go here and go to the auto sections put in you car make and model year, there it will show you what bulbs go where

User Avatar

To replace the bulbs in a 1997 Acura safely prop the hood open. Locate the front headlights and remove the old lights. Replace the bulbs.

User Avatar

Changing the instrument panel lights require removal of the dashboard. With the dashboard removed pull the gauge cluster out and take off the bulbs. Install the new bulbs.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.