Removing the taillights
To access the taillights one needs remove the taillights cover. To do this open the trunk, in the trunk are three plastic bolts that hold the taillights cover on. To have easier access to these bolts pull the trunk fabric a little away from the bolts. Unscrew these, then from the outside of the car pull the taillights cover toward you. Once the taillights cover is dislodged from its spot in the body of the car. You should have full access to all the individual lamps once you do this.
No, the fog lights have a switch.No, the fog lights have a switch.
turn signals won't work. changed all the bulbs. Hazard lights work. 1999 Chrysler Sebring hardtop
I have a 1998. I have never used the lower lights. Recently asked at the dealership how to turn them on. Lever on left of steering column where I turn on the headlights? The end of that lever pulls out, turning the lower lights on.
Blown fuse, failed bulbs, bad switches, etc.
I have a 2002 Chrysler Sebring convertible. If you turn off the ignition and remove the key while the headlights are on, then turn off the headlights, the headlights will stay on for 30 seconds and turn off. You can avoid this by turning the lights off before you turn off the car or by switching them on and off again.
To turn on the fog lights you pull the end of the turn signal lever it will pop out about 1/8th inch.
It is probably the brake lights that are on due to a misinstalled or damaged brake light switch.
the multifunction switch... ( turn signal) twist it to turn on the lights and once the lights are on pull it towards the door to turn the fog lights on
i used my key on the passnger side door to unlock it and my alarm souned off i tryed unpluging the all the computers and battrey and the horn and the lights keep flashing i have no key pad .
Could be a faulty relay!
On my 2001 sebring, my light lever is on the column. After turning on my lights, I gently twist the end portion of the lever out (toward the door) to get the fog lights on
A warning light on the dash board of a Chrysler Sebring that has an exclamation point has to do with the tire pressure monitor system. Another warning that is a solid light is referring to air leaking into the gas tank.
The primary causes for the lights to flicker inside on a 2002 Chrysler Sebring LXI is a loose bulb or wire. This can occur when the vehicle has experienced rough road conditions and excessive vibration.
it has a blown fuse
If it does not turn over, but the lights work, you have a bad starter.
The part number for a 2000 Chrysler daytime running lights relay will be different for each manufacturer. Standard Motor Products sells this part as number RY-254.
Open the drivers door, remove panel on left side of dash. This panel is covered when the door in closed.
They went from the hide-a-way lights to the molded lens in 1993.
Push the snowflake button.....the button has a little light that lights up when you push it so you know it is on....
EGR Valve is dirty, or stuck open. Replace or better yet change.
on the same switch that turns your head lights on...you should see a little pull switch at the tip, when you turn on the headlights pull it out...it will not work unless the headlights are on
Turn headlights on by rotating the switch forward, and then pull outward on the knob to the left. Fog lights will also turn off with use of high beams.
Possibly a bad brake light switch, or bad connection.
inside your trunk there are 3 plastic nuts, one or two are actually holding the felt/carpet in place, the other(s) are farther behind it. remove them and you have access to all your lamps. reverse the process and you're done.
The rheostat in the light stalk is dirty and getting a bad connection causing the dash lights to flicker dim to bright and so on. Try turning the reading and dash lights on and off several times moving the rotary switch from all the way off to all the way on abd back several times. This sometimes will clear the problem for a period. If not, the light stalk will require replacement.