0
Need more information. If you are still interested open a discussion page.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace a 15 amp breaker in the circuit box?
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
What would cause circuit breaker to trip in new box from old box?
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
How do you install electrical wiring for room aircon?
More information is needed, maybe a lot more. Depending on its size you may need a new circuit for it. If you trip the breaker then don't use it and get a new circuit installed for it on its own breaker. You are probably talking about a window unit. If it is a simple 5000 BTU unit you can probably plug it into the nearest receptacle. If you trip the breaker then you need to run a new circuit for it. If it is much larger you may need to run a new circuit. If it is a 240 volt unit then you need a new circuit.
Can you add a second main breaker box to control breakers in the out buildings on a farm?
yes. But this is not a handyman level project. It is suggested you "Call a pro." What you're looking for is not another "main breaker" but a "sub-panel" that is fed by a "feeder" cable from the main panel. Have your electrician calculate the load you'll need in the out-building, then design and install a new feeder circuit and sub-panel for it.
How do you hook up a 15 amp breaker to a 60 amp box?
If by "60 amp box" you mean a 60-amp service panel (circuit breakers or fuses), you would generally get a 60-A panel that has several slots designed to accept a variety of compatible breakers, from 15A to 60A. If you have a "box" with no breakers, you would need another "subpanel", with wires from the 60A box to the new subpanel, and install one or more 15A breakers in the subpanel. If you don't need more than one breaker, you might also simply use a 15A disconnect panel with a single breaker in it.
How do you replace a 15 amp breaker in the circuit box?
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
What would cause circuit breaker to trip in new box from old box?
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
How do you install electrical wiring for room aircon?
More information is needed, maybe a lot more. Depending on its size you may need a new circuit for it. If you trip the breaker then don't use it and get a new circuit installed for it on its own breaker. You are probably talking about a window unit. If it is a simple 5000 BTU unit you can probably plug it into the nearest receptacle. If you trip the breaker then you need to run a new circuit for it. If it is much larger you may need to run a new circuit. If it is a 240 volt unit then you need a new circuit.
How do you add wires in your house?
First you need top check to see if you have space in your circuit box. If so a new breaker can be added and wires ran from that new circuit to any new location where additional electric is needed.
How can I find a short in my wiring that keeps popping the breaker?
The first thing to do would be to unplug everything that might be plugged into that circuit. It might be an external device that is tripping the breaker. If you know an electrician see if he will help you as thing can get complicated with this type of troubleshooting.Usually the wiring in the wall does not fault unless someone has driven a screw or nail into it. The fault will be in the junction box so look for burn marks inside the junction boxes. It could be as simple as a ground wire touching the "hot" terminal of a switch or plug that has just be changed out for a new one. If there was some DIY work done on that circuit, check that part of the circuit out first.The very first thing to do is to turn the breaker off, remove the electrical circuit from the breaker that is tripping and then turn the breaker back on to determine that it is not a faulty breaker. With the circuit wire removed from the breaker, the breaker should not trip. If it does change the breaker out for a new one.The second part of trouble shooting the circuit is going to entail turning the breaker on and off with exposed wiring open at junction boxes. If you are not confident that you can do this, hire an electrician. Trouble shooting this type of electrical fault is time consuming. I like to determine where the middle of the circuit is and open that junction box first. This will let you know if the fault is upstream or downstream from this junction box.Once you determine approximately where the middle junction box of the circuit is, it has to be opened and the wires removed from the device that is located in the box. Make a detailed diagram of how the device is wired into the circuit and what wires are spliced together in the back of the box that you are working on so that the box can be reconnected the same as before you took it apart. Once the wires are all seperated from each other, turn the breaker on and see if the breaker trips off.If it does not then the fault is downstream from this box. Put the wiring back together the same as it was and move on to the next box downstream and do the same procedureon that junction box. If the breaker trips then the wiring has a fault between the breaker and the box you chose to open the circuit at. Again put the wiring back together the same as it was and move on to the next box upstream and do the same procedure on that junction box. Continue with this same type of procedure until you find out what junction box connection is tripping the breaker.
Where is the circuit breaker on a new beetle?
on top of battery
Is it unsafe to have 60A service going into a new electrical box designed for 100A?
Its not recommended because your new main breaker will allow up to 100 amps and your old wire can only safely handle 60amps. If you put a 60amp main breaker in the new box, that would be acceptable. No, it is perfectly safe. Because the box is overrated, there is no problem. If the box is the main panel, and not a subpanel, install a 60A main breaker so you cannot overload your service. If it is a subpanel this 60A breaker should be in the main panel.
Can you add a second main breaker box to control breakers in the out buildings on a farm?
yes. But this is not a handyman level project. It is suggested you "Call a pro." What you're looking for is not another "main breaker" but a "sub-panel" that is fed by a "feeder" cable from the main panel. Have your electrician calculate the load you'll need in the out-building, then design and install a new feeder circuit and sub-panel for it.
How do you hook up a 15 amp breaker to a 60 amp box?
If by "60 amp box" you mean a 60-amp service panel (circuit breakers or fuses), you would generally get a 60-A panel that has several slots designed to accept a variety of compatible breakers, from 15A to 60A. If you have a "box" with no breakers, you would need another "subpanel", with wires from the 60A box to the new subpanel, and install one or more 15A breakers in the subpanel. If you don't need more than one breaker, you might also simply use a 15A disconnect panel with a single breaker in it.
What is a ark fault circuit breaker?
install breaker in panel and put the hot wire on the breaker and also there should be a place for the neutral on the breaker also both wires will be landed on the breaker in different spots and then take the white wire that is coiled on breaker and land it on the neutral bar
How does a solid state circuit breaker works?
Recently a new technology "solid state' are applied to traditional circuit breaker. This technology has resulted in freeing circuit breaker from arcing and switch bounce, also offering higher reliability and longer lifetimes and a faster switching time.
How do I get 220 volt circuit?
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
