answersLogoWhite

0


Best Answer

You will need the special fuel line tools available cheap at your local autoparts store.

User Avatar

Wiki User

17y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do remove fuel lines from the intake manifold fuel rail?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where is the fuel pressure regulator on a 97 Chevy C1500 pickup?

It is inside the upper intake manifold. To get to it you must remove the throttle body, upper intake manifold, and several electrical lines and fuel lines.


How do you remove intake manifold on a 1990 Acura Integra?

The intake manifold on a 1990 Acura Integra connects to the head of the engine. Loosen all of the nuts from the manifold to the head, disconnect the throttle body, vacuum lines, fuel injectors and coolant lines then pull the manifold from the head.


How do you change the fuel distributor in Chevy Blazer?

You must take off the upper intake manifold and it is right there. Depending on the year it is generally quite simple. You have to remove the top plastic vortec cover. Then remove the throttle cables. After that there are some sensor wires and 3 vacume lines. 1 vacume line is under the throttle body and the other 2 are behind the intake manifold. Then remove the coil to the ignition. After that there are 10 bolts to the intake manifold. Once you have the off remove the upper intake manifold gasket and then the fuel distrubutor lifts up and out. No bolts holding it in but the fuel lines can be a pian (at least some of mine were)


Remove and reinstall intake manifold on Saturn 19 engine?

First remove serpentine belt, loosen power steering mount bolts and remove, leave lines hooked up. Remove hose clamp holding intake hose to intake manifold from air filter. Remove fuel line and any vaccum hoses that wont remain with the manifold when it is taken off. Remove the fuel rail gently from the injectors. Remove all the nuts from the intake manifold, there is one nut down low on the passenger side of the manifold that is hard to get at and even see, I had to use a mirror so I could see to get my tools in place. Good luck


Location of fuel filter on4-cylinder Toyota truck 1984 R22?

Follow the fuel lines from the fuel tank forward to the engine and you will find the filter. Some have it located underneath the intake manifold, where it is very hard to see and change. Remove the Wheel for better access if you find it there.Follow the fuel lines from the fuel tank forward to the engine and you will find the filter. Some have it located underneath the intake manifold, where it is very hard to see and change. Remove the Wheel for better access if you find it there.


How do you remove the cover box to get to the fuel injector in Envoy 2002?

To remove the cover box to get to the fuel injector on the 2002 Envoy, first remove the intake manifold and the valve cover. You can do this by loosening the four bolts that hold the intake manifold first.Ê


Installing intake manifold on 1998 town Car?

To install intake>(1)drain coolant from radiator(2)release fuel pressure from fuel rail at fuel access port.(3)remove upper radiator hose and water neck.(4)remove injector hold down bolts and fuel rail hold down bolts and remove fuel rail assem. and injectors.(5)remove EGR pipe at fitting. (6)remove intake manifold bolts and remove intake manifold(7)remove old intake gaskets and clean head surfaces. Install new intake in reverse order of removal.


Where is the fuel pressure regulator on a 2000 Chevy blazer?

If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold. The throttle body is mounted on it and your fuel lines terminate into the center of this.


Where are the fuel pump relay and the fuel pressure regulator on a 1994 Chevy Blazer S10 4.3L It is running very sluggish especially uphill fuel pump and fuel filter are good and plugs were changed?

the fuel pressure regulator is located inside the polycarbonate(black plastic looking) intake manifold. You have remove intake manifold from the engine and "split" it apart on a workbench or suitable supporting device because the bolts that hold the 2-piece intake manifold together are located on the bottom of the manifold. the fuel pressure regulator is located inside the polycarbonate(black plastic looking) intake manifold. You have to remove the intake manifold from the engine and "split" it apart on a workbench or suitable supporting device because the bolts that hold the 2-piece intake manifold together are located on the bottom of the manifold.


Where is the fuel pressure regulator on a 2000 Chevrolet Malibu?

under neth intake manifold replae fuel lines while your under there.


How do you change an intake manifold gasket on a 2003 Ford Ranger.?

The intake manifold gasket is located between the manifold and the engine block, and prevents leaks between the two surfaces. Follow the below steps to replace the intake manifold gasket on 2003 Ford Ranger. 1) Disconnect the cable to the negative terminal of the battery and remove all hardware and wiring that connects to the intake manifold. Now disconnect the throttle position sensor and the EGR valve, located adjacent to the intake manifold. 2) Remove the fuel lines from their respective connections to the fuel injectors. Plug the fuel lines to minimize fuel spilling. Disconnect the intake manifold runner control cable from the manifold. 3) Label the spark plug wires and pull from the boot to remove from their corresponding spark plugs. The spark plug wires must later be connected to the same plugs in order for the cylinders to fire in the correct order. 4) Remove the bolts that hold the intake manifold to the engine block, and remove the manifold. Pry the intake manifold gasket from the block with a flat-head screwdriver. Clean the top mating edge of the engine block thoroughly. The surface where the new intake manifold gasket will rest must be smooth and free of debris. 5) Apply sealant to the gasket surfaces and place it on the mating edge of the engine block. Position the new intake manifold so that it aligns exactly with the cylinder flanges of the engine block. Bolt the intake manifold to the engine block. Tighten the bolts to 22 foot-pounds with a torque wrench. 6) Reconnect the spark plug wires with their corresponding spark plugs. Pull the boots over the spark plugs. Replace all removed parts in their original positions. Reattach all of the fuel lines to the fuel rails and fuel injectors. Reconnect all electrical wiring to its respective part. 7) Connect the cable to the negative terminal of the battery. Start the engine and let it idle for about ten minutes. Check for leaks around the new intake manifold gasket.


Where is a knock sensor on a 2002 chev silverado?

Underneath the intake manifold, there is a front and rear, under a rubber seal with a wire leading to the sensor. You will need to remove wiring and lines above intake, and disconnect fuel line to rails before removing intake. You do not need to remove injectors.