0
How do the starter wires go on a 95 sunfire2.2 engine
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you change the starter in a 99 sunfire 22 liter?
Disconnect the negative battery cable at the battery. Raise and safely support the vehicle. Remove the electrical connections from the back of the starter. Remove the bell-housing cover. Remove the starter support bracket bolt from the engine block. Unfasten the starter motor-to-engine bolts, then carefully lower the starter. Remove the nuts/bolts that hold the starter support bracket to the starter. To install: Transfer the starter support bracket to the new starter if the starter is being replaced. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm). Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm). Install the bell-housing cover. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm). Carefully lower the vehicle, then connect the negative battery
What is the windshield wiper size for a 1998 Pontiac Sunfire?
22 and 17
Where is the air intake temperature sensor on a 1997 Pontiac sunfire with a 22 engine?
It's on the black tube between the airbox and the throttle bodies. It'll be around 1/2 way along it.
What kind of ammunition do you put in a EIG volcanic 22 starter pistol?
22 pistols usually take 22 shorts and all starter pistols take blanks.
What is the windshield wiper size for a 2001 Pontiac sunfire?
18'' and 22'' pretty sure.
22 RE 86 Toyota truck will turn over but will not start what is the problem?
the starter. if you know where it is you can hit it and see if this helps. you need to see if you have spark at the plugs if so check to see if you have fuel the starter only turns the engine
Size windshield wipers for the 1995-2005 Pontiac Sunfire?
Here they are:Driver side: 22"Passenger side: 17".
What is the Value of volcanic 22 starter pistol?
25 USD or so
What is the difference between fs-2 and fs-22 starters?
is a fs 2 starter comparable to fs 22
How do you install a starter on a 1994 Buick Regal?
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c15280067b76 2.8L and 3.1L Engines 1988-94 VEHICLES See Figures 5, 6, 7 and 8 # Remove the air cleaner and duct assembly. # Disconnect the negative battery cable. # Raise and safely support the vehicle. # If equipped with an engine oil cooler, drain the engine oil, remove the oil filter and position the hose next to the starter motor to the side. # Remove the nut from the brace at the air conditioning compressor, nut from the brace at the engine and the brace. # Unfasten the retaining bolts, then remove the flywheel inspection cover. Fig. 5: Unfasten the retaining bolts ... Fig. 6: ... then remove the flywheel cover # Remove the starter bolts and shims, if equipped. Do not let the starter hang from the starter wires. Fig. 7: An extension may be needed to access the starter mounting bolts Fig. 8: Remove the starter motor and any shims that may have been used # Detach the starter wires from the solenoid, then remove the starter from the vehicle. To install: # While supporting the starter, connect the starter wires at the solenoid. # Install the starter motor-to-engine mount with the shims, if equipped, and the mounting bolts. Tighten the bolts to 32 ft. lbs. (43 Nm). # If equipped with an engine oil cooler, reposition the hose next to the starter motor, install the oil filter and refill the engine with the proper amount of engine oil. # Install the flywheel inspection cover and tighten the bolts. # Install the starter support brace to the air conditioning compressor and tighten the nut to 23 ft. lbs. (31 Nm). # Carefully lower the vehicle, then connect the negative battery cable. # Install the air cleaner and duct assembly. 1995-96 VEHICLES See Figure 9 # Remove the air cleaner and duct assembly. # Disconnect the negative battery cable. # Raise and safely support the vehicle. # Remove the oil filter splash shield. # Detach the starter electrical connector(s). # Unfasten the starter mounting bolts, remove any shims, then remove the starter from the vehicle. Fig. 9: Starter motor mounting-1996 3.1L engine shown To install: # Position the starter to the engine. Install the mounting bolts and shims (if equipped). Tighten the bolts to 32 ft. lbs. (43 Nm). # Attach the electrical connector(s) to the starter. Tighten the starter solenoid switch BAT terminal outer nut to 84 inch lbs. (9.5 Nm) and the starter solenoid switch "S'' terminal nut to 22 inch lbs. (2.5 Nm). # Install the oil filter splash shield. # Carefully lower the vehicle, then connect the negative battery cable. # Install the air cleaner and duct assembly. 3.4L Engine See Figures 10 and 11 # Disconnect the negative battery cable. # Remove the engine oil cooler assembly. For details, please refer to the procedure located in of this repair guide. # If equipped with an automatic transaxle, unfasten the flywheel inspection cover bolts, then remove the cover. # Detach the electrical connections from the starter. Fig. 10: Detach the starter electrical connections ... Fig. 11: ... then unfasten the retaining bolts and remove the starter from the vehicle # Unfasten the starter motor retaining bolts, then remove the starter. To install: WARNING Before installing the starter to the engine, make sure the electrical terminals are secure by tightening the nut next to the cap on the solenoid battery terminal. If this terminal is not tight, starter damage may occur. # Secure the electrical terminal on the solenoid. Tighten the solenoid battery terminal inside nut to 84 inch lbs. (9.5 Nm). -27 inch lbs. (22-27 Nm). # Position the starter motor, then install the retaining bolts. Tighten the bolts to 32 ft. lbs. (43 Nm). # If equipped, install the flywheel inspection cover and tighten the retaining bolts to 89 inch lbs. (10 Nm). # Install the engine oil cooler assembly, as outlined in of this repair guide. # Connect the negative battery cable. 3.8L Engine 1991-92 VEHICLES See Figure 12 # Disconnect the negative battery cable. # Remove the right side cooling fan. # Remove the serpentine drive belt, as outlined in of this repair guide. # Disconnect the A/C compressor upper support brace, then lay the compressor in the fan opening. # Raise and safely support the vehicle. # Detach the engine oil cooler lines at the flex connector. # Unfasten the retaining bolts, then remove the flywheel inspection cover. # Remove the starter motor retaining bolts, carefully lower the starter and remove the shims, if used. # Detach the starter motor wiring, then remove the starter from the vehicle. Fig. 12: Starter motor removal and installation-1992 3.8L engine shown To install: # Attach the electrical connectors to the starter terminals. Tighten the battery terminal nut to 80 inch lbs. (9 Nm) for 1991 vehicles and to 12 ft. lbs. (16 Nm) for 1992 vehicles. Tighten the "S'' terminal nut to 27-35 inch lbs. (3-4 Nm). # Position the starter motor and shims, if used, to the engine and tighten the mounting bolts to 32 ft. lbs. (43 Nm). # Install the flywheel inspection cover. Tighten the retaining bolts to 89 inch lbs. (10 Nm). # Attach the engine oil cooler lines at the flex connector. # Carefully lower the vehicle and position the A/C compressor. # Install the A/C compressor upper support brace. # Install the serpentine drive belt, as outlined in of this repair guide. # Install the right side cooling fan # Connect the negative battery cable.
Where do you get blanks for 22 starter pistol?
Gun Shops and if a sporting goods store sells starter pistols they will most likely sell blanks. There are 22 blanks that are used to drive nails into concrete. They come different power levels and should work for blanks in a starter pistol. Any lumber supply should carry them.
What is the height requirement of telephone wires according to the national electric code?
22 ft
