There are raised ridges oon the plastic timing cover that provide the timing marks
The timing marks on a 1991 Toyota Tercel are on the crank pulley. They are located on the front of the pulley and under the cam.
Were are the timing marks on a 1991 acura legend
My 1991 Geo Prizm LSI does not have overdrive My 1991 Geo Prizm LSI does not have overdrive
Wich marks can u use to set it on time if the marks are erased
1991 mercury cougar i need to know the egnition timing engine is a 3.8 v6.
Timimg marks are on the harmonic balancer and pointer is on the lower timing cover
getting the marks aligned correctly is important to insure the amount of power you will have.
TIMING MARKS - '91 EXCELI would very much appreciate an answer to the following question: How do I line up the timing marks to a 1991 Hyundai Excel (so that I know I've correctly set/repaired the vehicle)?Because the marks to be aligned are beneath the level of the fender, you need to use a mirror to ensure that the timing marks are properly aligned.But where do the timing marks have to be lined up with please???
i need to know the timing marks on Mitsubishi pick up 1991 2.4 one cam
Timing marks are always on the crankshaft, usually on the pulley closest to the block. This is because the timing must be based upon the position of the number one piston, which is connected to the crankshaft.
Get a manial on your car. It will keep you from making mistakes
i had 1991 geo prizm but i want to know what color memory wire??
as regulated air and fuel ?
No, It will not,just put on a new one and set the timing marks according to the book.
On the front side of the engine towards the passenger side of the block, there is a small rubber insert just below the head (near the #4 exhaust port. ) If you remove the rubber stopper a pointer and the timing marks will be visible.
there are timing marks on both cam pullys and a timing mark on the crank pully as well. you have to have them all aligned to the marks on the inner timing cover, which is virtually strait up and down on all three. and you must also match the timing lines on the new belt up with the timing marks on the pullys. be sure not to roll any of the pullys backwards (counterclockwise) or you could cause some major valve damage.
Connect timing light to battery and No. 1 cylinder and aim light at crankshaft Connect timing light to battery and No. 1 cylinder and aim light at crankshaft timing marks
Providing that you used a shop manuals info, everything should be working fine. However, if you did not set the timing marks to match before you removed the old belt (or even if it broke off) it won't start.Also, try reasing any trouble code from the computer, by disconeecting the neg bat terminal for like 10 secs. In reality you have not stated what made you replace the belt in the first place, understand.If it was that the belt broke off while driving, then I do hope you set the timing marks at the lower crankshaft and upper Camshaft. (there are marks for this). That's why its important to have the vehicles shop manual. Also, I hope you used a timing light to do the final touch. good luck.AnswerThe upper timing mark is really hard to see clean off the bearing housing behind the cam gear mark it with a whiteout pen or touchup paint then align the crank timing using the same method. As for your ground and resetting the ecu I hope you pulled ground before doing a timing belt>? Once you get the belt on turn the car over by hand twice min. Look and see if your timing marks align still. If they don't then pull the belt and do it again. It's easy to jump teeth.
Here is the link to ehow on how to remove the CV joint on a 1991 Prizm. http://www.ehow.com/how_7906772_replace-geo-metro-cv-joints.html
there is only one mark and one pointer
Yes, A 1991 civic uses a timing belt, not a timing chain.
timing marks ,they are rigth on the gear box get the piston #1 all the way up and make sure the mark rigth on the gear box where the gap is in 0 and the rotor pointing the piston one and that's it it should work excuse my English i am Mexican .
In the fuel tank
it is attached to the engine