answersLogoWhite

0


Best Answer
Copy

on the side of the thermostat housing there is a small screw with the motor is running make sure the heater is on loosen the screw let the water run until you see a steady flow then tighten back up.

I disagree with the previous poster. The cooling system is bled by loosening the screw on the metal pipe just behind the water pump housing. The pipe goes upward off the housing and has a bleed screw on the end of it.

To Bleed the cooling system, turn the heater to full hot and open the screw and add coolant to the resevior until you get a bubble free flow of coolant from the bleed screw. At this point the system is bled and just tighten the screw.

User Avatar

Wiki User

โˆ™ 2015-07-15 18:40:17
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you bleed all of the air out of the cooling system on a 1995 Pontiac Grand Am with a 3.1?
Write your answer...
Submit

Related Questions

How do you bleed cooling system on pontiac 2.4?

To bleed the cooling system on a Pontiac 2.4 engine, there is a small hose near the bottom of the radiator that needs to be removed. Then remove the radiator cap and the cap on the radiator overflow tank.


How do you bleed air out of cooling system?

how to bleed air out of cooling system 1997honda civic ex


How do you bleed a diesel 1500 CC Peugeot 106 cooling system?

how do you bleed a diesel peugeot cooling system


How do you bleed the cooling system 1995 Nissan questafter the thermost has been replaced?

There is no reason to ever bleed a cooling system.


1988 Acura Legend bleed cooling system?

How do you bleed the cooling system of a 1988 acura legend? Is there a bleeding screw and where is it located?


When do you bleed a radiator 1996 Monte Carlo ls?

Any time you flush out the cooling system you need to bleed the cooling system.


How do you bleed air out of cooling system Chevy Blazer 4.3?

If the cooling system is in good working order the system will bleed the air out itself. If the system has a leak anywhere no matter how small the system will never bleed the air out.


How do you bleed air from a 2006 Chevy impala 3.5 cooling system?

there should be a air valve on the engine that you can bleed the bubbles out of the cooling system.


Do you have to bleed the brake fluid from a 99 Pontiac grand am when changing?

yes


How do you bleed the coolant system properly on 2002 Jeep Grand Cherokee?

Open the t/stat bleed valve or if there is a radiator petcock. run the engine while servicing as they are prone to air pockets in the cooling system.


If the low coolant light is on when you just replaced the radiator in a 1994 Pontiac Grand Am with a sealed radiator system what could be the problem?

There is a high probability that the system needs to be bled. As in bleed the air from the system. Just filling the system is not enough. You need to warm the engine to get the water flowing, then switch off and bleed the air out. Yes there is always some air and it gravitates to the highest point of the cooling system. I hope this helps


How do you bleed the air out of the coolant system on a 2000 grand am?

when it is cold take the cap off the radiator and start the car and let the air out The above answer is incorrect. The cooling system on the Grand Am requires you to bleed the system. There is a bleeder screw on the top of the motor, just follow the black tubing and you'll see it.


Do you have to bleed the cooling system after changing a radiator hose?

NO!!!!!


How do you bleed the air from the Engine cooling system on Chevy truck?

Engine cooling system is not a closed system you can't remove the air.


How do you bleed the air out of the fuel system on a 2000 Pontiac Grand Am?

There is a schrader valve on the fuel rail that will allow you to blled the system. This is not normally necessary as the air will be pushed out by the fuel pressure.


Where is the bleed valve for the cooling system on 5.7 liter gm suburban?

The cooling system bleed valve, on your General Motors 5.7 liter engine, is located on the bottom of the radiator. The bleed valve should be in the middle of the radiator bottom.


Bleed air from clio cooling system?

There are various ways to bleed air from Clio cooling system. The best option is to run the system for a while with the cap up while making increased revs. Ê


How do you bleed air from the cooling system of a Chrysler Concorde?

The bleed screw is by the thermostat housing it looks like a brake bleed screw


Citroen berlingo 1.9 van where are air bleed points on cooling system?

how does engine cooling system on berlingo 1.4 work


How do you bleed the cooling system on a 1995 Lincoln?

you dont bleed cooling systems you have to take it to a mech. shop or have the proper equipment and the r-134a on hand to do it your self.


How do you bleed cooling system of 1993 Mercury Villager?

There is no need to do this normally.


Do you need to bleed the cooling system on a perguot 206?

Should bleed all vehicles after the system has work done to it to get rid of air pockets


How do you bleed the cooling system 96 acura 3.5 tl?

To bleed the cooling system on a 96 Acura 3.5 L, cool the radiator and remove the radiator cap. Loosen the drain plug and drain.


Still no power steering after changing the power steering pump and rack and pinion in 96 Pontiac grand am what next?

have you tried removing return line to bleed system ?


How do you bleed air pocket from cooling system?

drain the whole cooling system and refill it. You will never know if you don't give details of your car!