answersLogoWhite

0

  • Clutches and Flywheels
  • Nissan 240SX

How do you bleed the clutch line on a Nissan 240SX?

User Avatar

Wiki User

โˆ™ 2007-02-15 11:16:11

Best Answer
Copy

The same way you bleed brakes, but use the little bleeder valve on the slave cylinder. The same way you bleed brakes, but use the little bleeder valve on the slave cylinder.

2007-02-15 11:16:11
This answer is:
๐Ÿค“
๐Ÿคฏ
๐Ÿค”
User Avatar

Your Answer

Loading...

Related Questions

The clutch pedal on your 89 240sx sticks to the floor it has a new clutch what do you do?

Bleed the slave cyl. It probebly has air in the line or no fluid.


Why will the clutch not pump but will stay all the way up or down in a 1990 Nissan 240SX with manual transmission added clutch fluid?

I would suspect that the clutch slave cylinder is bad. Follow the line down from where you added fluid to find the slave cylinder. After replacing the slave unit you will need to bleed the system then it will work fine again. Mark


How do you bleed the Mercedes c180 clutch?

You can bleed the clutch by loosening the fluid line. With the line loose pump the brakes until fluid comes out.


How do you bleed the clutch line on a 2004 ford ranger edge?

how do I bleed the clutch system in a 2004 ford ranger


What can the problem be when a 91 Nissan sat for a long time and the clutch pedal is stuck to the floor?

check your clutch fluid lines and your clutch fluid and also bleed the clutch and it should work just fine mine did the same thing and i had to replace a clutch line that was pinched


If you just replaced the clutch master cylinder on a Nissan 240sx then why won't it build up pressure?

The most likely case would be that air somehow got into the line. try bleeding the clutch fluid, while making sure that the level in the reservoir does not get low.


How do you bleed the air in your clutch line on a 1997 gmc sonoma?

same as bleeding the air in the clutch line for any other car -stab the air.


How do you bleed the hydraulic clutch line on a 1989 Chevrolet half ton?

FIRSY FILL THE CLUTCH FLUID RESEVOIR AND THEN BLEED BY LOOSENING THE BLEEDER NIPPLE ATTACHED TO THE SLAVE CYLINDER.


How do you adjust a clutch on a 1987 Pontiac Fiero?

There is no clutch adjustment. The clutch is hydralic and therefore needs no adjustment. If the clutch isn't working correctly you most likely have to bleed the clutch line.


What is the cause of a 97 elantra clutch pedal getting completely stuck?

You need to bleed your clutch master cylinder line.


Why does your 1986 Nissan pick up it leaks the clutch oil by the transmission?

Is the leak coming from your slave cylinder,it has two bolts holding it on,with a rubber cover,if so ,you need to replace and bleed it and your clutch damper,its on the left side of fire wall,just follow your clutch line from clutch master cylinder,20.00 for slave cylinder.,


Where is the clutch bleed nut on a jeep yj?

Look at the same location as the clutch line going into the trans, but on the other side ( passengers side ) the bleed valve will be on a line exiting the bell housing top passengers side. Remove the access panels around your shifter and you will see them both, and another nifty thing is that with it right there you can bleed the clutch without help.


How do the timing marks line up on a 1992 Nissan 240SX 2.4 engine?

Get a manual on your car, It will have pictures and everything,.


How do you adjust a hydraulic clutch on a 1989 jeep--- what i mean is you have to push the clutch all the way to the floor to change gears. is there air in the line is there a way to bleed the line?

hydraulic clutch does not have adjustment. replace the clutch it has a slave cylinder underneath and what you do is pump up the clutch and then hold it and have somone turn the line going itno th slave cylinder until you have clear fluid that is not how you bleed a clutch to the jeep owner, if you know how to bleed brakes on a vehicle, then you know how to bleed the clutch on a vehicle both done the same way.now if no parts of the clutch, such as master or slave cylander have been touched or let run out of fluid, there is still no need to bleed as that will not be the problem you might look at the linkage on the slave cylander. sometimes there is nylon bushing on the cylander rod that wears out. replace this bushing which is easy to do and your clutch will be good again.


How do you bleed air outof clutch line on 92 Nissan pickup?

On the bottom right there is a slave cyl you take a ten mm wrench have someone pump the clutch hold it open the bleeder they will fill the pedal go down then tighten it repeat several times


On a 1990 Isuzu Amigo what would cause the clutch pedal to stick to the floor?

if its hydraulic there could be air in your line. bleed your clutch and refill.


How do you bleed a clutch on opel astra gtc?

Follow the clutch hydraulic line down to the bell housing. Note where the hydraulic line goes into the bell housing and if there is no bleed valve there you may need to remove a cover. Have a friend/assistant step on the clutch while you open the bleed valve. Close the valve and have the friend let up on the clutch. Do that a few times (making certain that the hydraulic fluid remains full) and you're done.


What do I do after installing new clutch 2005 corolla xrs the clutch pedal seems super free to push in also having a rough time moving in and out of gears as if misaligned?

Bleed the clutch line that runs from the clutch master cylinder to the slave cylinder utilizing the bleed valve on the slave cylinder.


How do you replace the clutch slave cyliner on a 1992 Nissan Stanza?

go to transmission and unsrew line from slave cylinder and drain fluid into container,remove two bolts holding it on,install new part with two bolts and tighten line up,fill clutch master cylinder up with dot 3 brake fluid and bleed,pump clutch pedal a couple of times and have someone open line to let air out,good luck...


Do you need to bleed line after replacing clutch master cylinder?

yes,open bleeder valve on cluch slave cylinder and clutch damper to release air.


What does the clutch bleed valve look like on a 92 jeep wrangler?

On the opposite side of the trans from where the clutch line enters, a fitting with a bleed valve on the end. You can get a great view if you remove the access panel around the shifter, you will be able to see them both from there, loosen the end to bleed.


When you replace clutch master clyender do you have to bleed the slave clyender?

yes you do,also if it has a cluch damper,you need to bleed it also,its bolted on left side firewall or just follow the line coming from clutch master cylinder.good luck.


What does the clutch stay down instead of popping back up?

It sounds like there is air in the clutch line somewhere. Bleed the clutch (if possible, some clutches are "self-bleeding" and need to be replaced entirely).


How to adjust F350 Hydraulic Clutch?

Hyd clutch has no adjustment, pump clutch pedal hold down bleed off hydraulic slave cylinder on driver side of trans. If won't bleed replace if bleeds off no air in line & still not better ck bushings on clutch pedal under dash. Hope this helps


Where is the clutch bleed line in a 98 Toyota 4-runner?

at the caliper and drums derrr! at the caliper and drums derrr! no its under the car where the clutch line goes into the trani at. they should be a 8mm nippple sticking out