How do you bleed the clutch on a 1989 Chevy truck?

It is important to bleed a clutch master and slave cylinder to make sure all of the air is out of the lines. For a 1989 Chevy you would need to know model you had, and then find the repair manual for that specific vehicle.

Loosen the bleed valve

FIRSY FILL THE CLUTCH FLUID RESEVOIR AND THEN BLEED BY LOOSENING THE BLEEDER NIPPLE ATTACHED TO THE SLAVE CYLINDER.

Does the Hydraulic clutch pump brakes alot on 1989 chevy berette gtu 2.8liter 6cyclinder 5speed

No, It is not even close.

there is a joint AT THE BOTTOM OF THE CLUTCH AND A BOLT U TIGHTEN THAT AND U ARE DONE I DID IT TO MY TRUCK

Neither the front or rear bumper of a 1989 Chevrolet truck will fit on a 1989 Dodge truck. The bolt patterns are different and will not line up.

YES they are the same.

yes as long as they are both v6s or v8s

Yes it will.

YES, That would be a direct swop.

In the gas tank

behind the glove box

There are more variables that you would need to know to get the blue book value of a 1989 short bed Chevy truck, such as mileage, condition, options, and location.

Yes it should

Yes, it is all the same.

.035 in a 1989 k 2500 truck.

you should try to poo in it

Yes they are the same.

no gas no power

hydraulic clutch does not have adjustment. replace the clutch it has a slave cylinder underneath and what you do is pump up the clutch and then hold it and have somone turn the line going itno th slave cylinder until you have clear fluid that is not how you bleed a clutch to the jeep owner, if you know how to bleed brakes on a vehicle, then you know how to bleed the clutch on…

The estimated cost to replace a clutch and radiator, in a 1989 Nissan pickup truck is $1100. A private mechanic may be able to do the job for less.

1988 to 1991 most parts are interchangeable - body styles an other things changed after 1991

Not 100% sure about the Toyota truck, but I had that same problem with a late 90's Chevy. Turned out to be the clutch fan ($25 part) after I had replaced almost everything in the cooling system.

Your 1989 Chevy truck air-conditioner condensation drain can be found on the bottom of the air conditioner compressor. The air conditioner condensation drain routes condensation to the bottom of the engine compartment.

dont have one,check your slave cylinder for leaks,if ok ,then u need a new clutch.

Passanger side, lower part of the engine.

No you can not , That is what makes and keeps the engine running

Check the fuse

That year did not have a cam sensor.

yes, it does have Oxygen sensors

bleeding and Transmission do not go in the same sentance...lol If you have a hydraulic clutch, that is another story :)

around 6000lbs depending on bed/cab configuration, endine and options, check the tag inside the driver door. A 1989 Chevy 1500 weight is between 4023 and 4748 lbs depending on trim level. Just FYI the tag inside the door does not give the weight of the truck it gives the hauling capacity. Which is the additional weight above the weight of the truck that the truck can handle on its on 2 axles.

its a chevy, so its too much for your mom and her

Distributor rotates clockwise.

check this site it should help

Left of the steering column, under the dashboard.

It depends on the height of the curb.

It's built into the water pump. You have to replace the water pump.

any seat belts from an 1981 through1987 Chevy truck or 1981 through 1989 blazer or suburban

the gross vehicle weight rating of a 1989 Chevrolet 2500 pickup is 8,600 lbs.

85W90 Gear oil.

Not without modifications and fabrication.

5 QTS. with new filter.

The rear gear ratio of a 1989 Chevy Cheyenne truck is between 2.73 and 4.56. This is the number of times the drive shaft rotates in relation to the tires.

You will find the bleeder valve on the Slave Cylinder, which is mounted on the front of the transmission, by the radiator. You will find it in the front and center of the engine compartment.

It will fit but you will have to get a shorter driveshaft. The truck transmissions are longer then a passenger car transmission.

Any hood from a Chevy/GMC from 1988 to 1999. Includes truck, Tahoe/Yukon, and Suburban.

They could be, it depends on the vehicle. On a dodge truck with the Cummins diesel from 1989-2002 it is left-hand thread for example.

Should be in a removable housing at the engine end of the upper radiator hose