answersLogoWhite

0


Best Answer
Copy

Just drained my coolant on a 1998 and had a hard time getting air out. I ended up filling degass tank almost to top idling engine for a short time . Then let engine cool and add more coolant had to repeat this procedure several times before heater would continue to blow warm air. Jeff

User Avatar

Wiki User

โˆ™ 2006-03-11 01:57:56
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you bleed the coolant system on a 2002 Lincoln Continental?
Write your answer...
Submit

Related Questions

How do you bleed air out of coolant system 97 Saturn?

procedure on how to bleed air out of coolant system on 97 saturn ls


How do you bleed your V6 coolant system?

how do i bleed my accord v6 2000 coolant system, its has air and the rev's gone up & down......


Where is the place you bleed coolant system?

It is not necessary to bleed the coolant system. If you mean "drain" the system, there is usually a plastic plug on the radiator or, you can pull the lower radiator hose off.


How Do you Bleed The Coolant System On A 1998 Beetle?

To bleed the coolant system on a 1998 VW Beetle, remove the top from the overflow tank. Run the car for 10 to 15 minutes to force any air out of the system, then check the coolant level. Add coolant as needed.


How do you bleed the coolant system on a 2002 impala?

There is a bleed screw on the thermostat housing. Remove the screw with the engine loose. Ounc you have pure coolant and no air you can close off the bleed screw.


How do you Bleed the coolant system on a 2002 Chevrolet Impala?

There is a bleed screw on the thermostat housing. Remove the screw with the engine loose. Ounc you have pure coolant and no air you can close off the bleed screw.


How Do you Bleed The Coolant System On A 1998 2.0 Beetle?

Start by taking the top off of the coolant overflow reservoir. To bleed the system, run the 1998 VW 2.0 Beetle about 10 minutes, then check the coolant level. Add coolant if needed, then replace the reservoir top.


How do you bleed coolant system after replacing thermostat?

what is the year make & modle of it??


How do you bleed the coolant system on a 1999 mercury villager?

Not necessary on this vehicle.


How do you bleed my coolant system?

As you did not include engine or Year info I will give a general answer. Look on the top of the engine, most GM products with a bleed system have a small brass pipe thread plug in the top of a black or aluminum casting. This is the bleed point, loosen the plug or valve and add coolant to the system until it flows from the bleed, tighten up the bleed. Done. Repeat if needed.


Bleed 3800 engine cooling system?

Is the question how to bleed a Buick 3800 cooling system? I would say open that little petcock by the themostat housing and release all the air as you fill the system with coolant. When coolant comes out instead of air all the air is out.


How to bleed air from coolant system in a 3.5 Olds Aurora?

Good luck haha..


How do you bleed the air out of the coolant system on a 1997 Pontiac Montana?

If it has bleeder valves then use them to bleed the system, if not, jack up the front of the vehicle as high as possible. Remove the radiator cap and start the engine. Add coolant to keep the system full. This will allow air to escape.


How do you bleed coolant at 1999 Subaru Forester?

You should not need to bleed coolant. Ever. If the coolant is filling up on its own the stuff in there is not coolant and you have a big problem.


Do you have to bleed cooling system on a 1989 ford probe after changing the thermostat?

If there is not bleed valve for the coolant you will have to do it manually. Fill the radiator up and start the car. After it warms up the coolant level will drop, refill it.


How do you bleed air out of a 1995 Intrepid 3.3 liter engine coolant system?

To bleed the coolant in a 1995 Dodge intrepid locate the drain plug on the underside of the radiator, un plug it and pour new coolant in the system. Close the plug and while the engine is running find the coolant pressure valve and loosen it to relieve pressure. When bubbles stop forming there is no longer air in the system.


Why after replacing the water pump on a 1996 Cherokee is there no heat?

Low coolant level or possibly air trapped in the system. Bleed the system and check the coolant level in the radiator not the reservoir.


Bleed coolant system in cadillac 4.6?

There is no need to manually bleed the coolant system on a Northstar, the system is self bleeding. The small hose on the side of the overflow tank is the self-bleed line. If, by chance, this line is obstructed, then the air will be trapped & cause overheating problems. Be careful is the plastic nipple on the side of the overflow tank as it is very weak & cracks easily.


Where is the coolant air bleed valve on 2000 Mercury Villager?

The Villager engine does not have a coolant bleed valve.


How do you bleed rack and pinion steering in a 1998 Lincoln Continental?

steering systems do not need to be bled, the air will be cycled out and into the reservoir.


Where is the bleed thumb screw on a 2000 Lincoln ls?

Next to the coolant reservoir... black hose sticking forward with a plastic screw in it...


How do you properly bleed cooling system on 1996 olds cutlass?

To bleed the cooling system on a 1996 Olds Cutlass, locate the bleed valve, which is on the front of the engine above the water pump. After making sure the cooling system is not under pressure, open the valve by turning it counterclockwise. Fill the radiator with coolant until no air comes out the bleed valve, and a stream of coolant begins to flow from there instead. Tighten the valve and close the system to finish the job.


How do you bleed the heater core?

If by "bleed" you mean drain, disconnect the lower of the two hoses (do not confuse with the pipes from the AC evaporator) and drain the coolant into a bucket. If you are flushing the system (which you should if you are changing the coolant anyway), dont bother draining it, most of the coolant will flow out anyway, just do the coolant flush and fill from the radiator.


Why is there small holes in some thermostats?

It is an air bleed hole, makes refilling the system with coolant easier.


Where is the bleed screw on a citroen c3 coolant system?

It is on the pipe behind the engine that goes to cabin radiator