answersLogoWhite

0


Best Answer

Ball joints on this car, like most, are pressed into the lower control arm. If you don't have a good pneumatic press, you either take the lower control arm off and take it to a mechanic, or just take the car to the mechanic. If the ball joint fails, the wheel falls off. Considering the importance of having the wheels stay on, I would let a mechanic with the proper tools handle this. I do brakes, shocks, struts, tie rod ends, half-shafts, engines, but not ball joints.

User Avatar

Wiki User

โˆ™ 2007-05-16 14:19:21
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you change a ball joint on a 1994 Plymouth Sundance?
Write your answer...
Submit
Related questions

How do you change the starter on a 1994 Plymouth sundance?

How do I change th starter on a 1994 Plymouth sundance


Is a 1994 Plymouth sundance an interference engine?

No, it is not an interference engine.


What if your Plymouth sundance 1994 code reads 3 what does it mean?

The codes on a 1994 Sundance are 2 digit codes. Code 3 is not correct.


1994 ply sundance how do you change front brakes?

Remove the tire and wheel from your 1994 Plymouth Sundance. Remove the brake assembly spring. The brake pads will come off. Reverse the process to install the new brakes.


Where do I find An oil dipstick for a 1994 Plymouth sundance?

You can purchase a dipstick from the dealer.


Where is the fuse for the heater blower located on a 1994 Plymouth Sundance?

in the fuse box


Where is the oxygen sensor on a 1994 Plymouth sundance?

It is screwed into the exhaust manifold on the rear of the engine.


How do you repair 1994 Plymouth duster speedometer cable?

A 1994 Plymouth Sundance/Duster does not use a speedometer cable. Instead, it uses a Speed Sensor located on the transmission.


Where is the camber located on your 1994 Plymouth Sundance?

Front camber is adjusted at the strut to knuckle bolts.


How do you change wheel bearing on 1994 Plymouth acclaim?

how do you change rear wheel bearing in 1994 Plymouth acclaim


Where is the fuel filter located on 1994 Plymouth sundance?

passenger side rear next to fuel tank


How do you change the lower ball joint for Mitsubishi diamante 1994?

How to change the lower ball joint for Mitsubishi diamante 1994


Is there access inside the car to remove the gas tank mounting bolts on a 1994 Plymouth Sundance?

No. It Is Held In Place From The Bottom .


What type of fuel pump comes with a 1994 Plymouth sundance 2.2L mechanical or electric?

Electrical located in the fuel tank


How do you replace the water pump on 1994 Plymouth Sundance?

It would greatly help to know what engine you have and if it has air conditioning (working or not)


Plymouth Sundance 1994 codes 43 55 mean?

Code 43 refers to the coil. Code 55 is end of message.


Where do you install the safety bolt for a child seat in a 1994 Plymouth Sundance?

My child seat car bolt, is in a 1988 Sundance, passenger side about 1 ft from behind back seat, on trunk floor.


If your flasher stays on like a light but doesn't flash what do you need to do in your Plymouth sundance 1994?

The bulb is falty, replace it and it should cure your problem.


Where is the rev limiter on a 1994 Plymouth sundance?

The engine computer is the rev limiter. It controls max rpm by shutting off fuel and ignition.


How do you change a heater core on a 1994 Plymouth Acclaim?

you have to remove the dash


Fuse chart for a 1994 Plymouth Sundance?

I just purchased a 1994 Plymouth sundance from my niegbor for dirt cheap (joe dirt) it has been sitting for about three years.just wanted to see if I could fire it up. put a new batt. in it . it cranks over but no fire I primed it with gas it fires and runs until gas burns out .I am thinking maybe a fuel pump from sitting so long! what do you think?


How to diagnose and repair backup lights on a 1994 Plymouth Sundance the light work intermittently?

Check grounds Check loose wire on switch Check defective switch


Where is the crank shaft position sensor located on a 1994 Plymouth sundance?

Under hood, driver side, upper engine area, mounted on end of engine block


Where is the modulator valve on a 1994 Plymouth?

A 1994 Plymouth does not have a modulator valve.


1994 Plymouth Sundance trouble code 11?

Code 11 means no camshaft position sensor signal detected during engine crankingFix : Replace the camshaft sensor