you basically have only 2 bolts to remove (2 different sizes) They are common household size. If you wish to replace the rotor as well you have only 2 more bolts to remove. Make sure you clean off as much brake dust or anything else as you can. With a C clamp take your old brake pad place it over the caliper piston and slowly SLOWLY tighten the clamp to make the piston go as far back as poosible. Slap on your new pads and/or rotors tighten everything down. Before you jump in your car and drive off make sure you pump your brakes with the car off(apply the brake pedal) till if feels stiff, not all cars after replacing brakes will have that new brake feel but aslong as the brake pedal doesn't hit the floor you should be good. Now you can drive your car.
Search "PDFTown.com-GeneralElectrical" for Mitsubishi in google, I will try post the link if I can find it. here is the link; http://pdftown.com/PDF-Mitsubishi-Mirage-1993-1996-Electrical-Manual.html
It's located on the firewall, looking from the front of the car..almost centered.
Located in the fuse box. Fcing the engine, the box is located on the the right fender.
in dash behing radio on right. small metel box mounted with one bolt.
This file has all the diagrams you need for the entire car! http://www.2shared.com/file/10432949/f9093489/9020Circuit20diagrams.html
If a 1993 Mitsubishi Mirage Coupe has rust on the roof, the problem can be solved with a product called Bondo. This material consists of a tape or screen and a patching solution that has to be mixed. Apply some solution, apply the screen and cover with the rest of the solution, smoothing out with a putty knife. Let dry thoroughly and sand if necessary to smooth further. Spray paint with a primer for metal.
Begin by removing the tire and wheel from your 1993 GMC. Remove the brake spring and the brake caliper. The brake shoes will come off. Reverse the process to install your new brake shoes.
The rear brake pads on your 1993 Ford Escort can be changed by removing the brake pad Springs and break caliper. The brake pads will come off. Reverse the process to install the new brake pads.
cylender head bolt torque for 1993 Mitsubishi expo
Remove the tire and wheel from your 1993 Chevy Lumina. Remove the brake assembly spring and the brake caliper. The brake assembly will come off. Tap on the rotor with a hammer or mallet. The rotor will slide off. Reverse the process to change the new rotor and brakes.
OK, what is your question?
yes...you may need some special body contorsion.
need diagram of rear brake lines for 1993 mercury topaz
A 1993 Mercury Cougar takes ( DOT 3 brake fliud )
3000gt Mitsubishi 1992 is jumping out of reverse
Ooh, this is a fun one. The water pump is driven by the timing belt, so you have to remove and replace that to change out the water pump. ~Pengauin
Entire assembly should unbolt and slide out giving access to the bulbs
How do you remove rear brake drum from a 1993 Toyota pickup?
take it to a brake shop. breaks are life or death in a car. if your too unexperienced to change them yourself take it in. its not worth loosing your life over 150 bucks.
Where is the transmission control module on a 1997 Mitsubishi galant
The 3.0L V6 is a Mitsubishi engine, all others are Chrysler.
Remove the tire and wheel from your 1993 Lincoln Town car . Remove the brake spring and break caliper. Remove the brake rotor by tapping on it with a hammer or mallet. Slide the rotor off. Reverse the process to install the new rotor and brake pads.
Lift the car on a jack, remove the tire, remove the brake shoe/caliper and remove the old brake pad. Put in the new brake pad, replace the brake shoe/caliper, replace the tire and lower the car to the ground.