Car Computers and Sensors
Dodge Intrepid
DIY Projects

How do you change a cam sensor on a 1994 Dodge Intrepid with a 33 engine?

101112

Top Answer
User Avatar
Wiki User
2008-10-21 11:49:24
2008-10-21 11:49:24

follow the top radiator hose back to the engine.....may be hot....and to the left side of the hose(where the hose connects)...there should be a plug on the motor, actually the timing case cover.....I think 2 bolts hold the unit in place...unplug it....because of repeated heat on the plastic...I guess....I got mine free without breaking.....and falling into the timing case. This is a magnetic type sensors....two magnets....carefull not to get metal shaves or fillings and reinstall...plug in....

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

how to change oil pressure switch in 2001 Dodge Intrepid I need to look at a diagram

User Avatar

where is the crankshaft sensor located on a 1993 dodge intrepid

User Avatar

1999 dodge intrepid is not starting I change crank and camshaft sensor and it stall will not start what can i do next.

User Avatar

how to replace a map sensor on a 2004 dodge intrepid.

User Avatar

The 1994 Dodge Intrepid O2 sensor is located on the outside of the air cleaner housing. The sensor is on the back side of the housing.

User Avatar

where is torque conversion sensor on my 1997 didge intrepid?

User Avatar

where is the thermostat located on the dodge intrepid 2004

User Avatar

the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.

User Avatar

It determines, in real time, if the air fuel ratio of the engine is rich or lean.

User Avatar

How do I change the oil pan gasket on a 1999 Dodge Intrepid with 3.5 engine, what is the proper torque for the bolts.

User Avatar

The engine diagram for an intrepid will be in the Dodge intrepid service manual. The manual can be bought through an auto parts, or possibly borrowed from the library.

User Avatar

It is on the left front of engine. Points at the left front cam shaft. UNplug the wire , unscrew bolt, and pull sensor out.

User Avatar

On the Minivan it is the sensor in the exhaust on the back of the engine in the exhaust manifold.On an Intrepid/LHS/Concorde it is the pass side above cat oxygen sensor.On the Minivan it is the sensor in the exhaust on the back of the engine in the exhaust manifold.On an Intrepid/LHS/Concorde it is the pass side above cat oxygen sensor.

User Avatar

There are four oxygen sensors on a 2002 Intrepid. There is one before, and one after the catalytic converter on each side of the engine.

User Avatar

It doesn't have a mass airflow sensor.

User Avatar

It is located on the exhaust, maybe a foot or so from the engine. which side?

User Avatar

Front of the engine, points at the driver side cam sprocket.

User Avatar

It is mounted to the passenger side of the transmission bell housing, just behind the engine.

User Avatar

Trouble code P0131 means:O2 sensor circuit low voltage (Bank 1 Sensor 1)

User Avatar

A Dodge Intrepid has never been offered with a 4 cylinder engine.

User Avatar

if its the 3.5L the sensor is right on top, at the front of the engine. the cam sensor is near it just to the driver side of the top of the engine. The intake has to be loosened enough to get the cam sensor out form under it. The crank sensor is easier to get out.

User Avatar

UNDER HOOD, CENTER, UPPER ENGINE AREA, MOUNTED IN FRONT DRIVER SIDE OF ENGINE BLOCK


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.