Car Computers and Sensors
Ford Windstar
Crankshaft Sensors

How do you change a camshaft position sensor 1995 Ford Windstar?

161718

Top Answer
User Avatar
Wiki User
2009-12-21 01:40:23
2009-12-21 01:40:23

Disconnect the electrical connector. Remove the two 7/32 screws holding it on, and replace it. On the 3.8L it is like a little distributor at the front of the engine in the top of the timing cover. It has been a while but I think it just has one screw and clamp holding it in. You should also have the engine on TDC #1 and mark the old one before you pull it out. This makes life a lot easier if the engine would by chance turn with the sensor removed. MGL

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Camshaft position is taken from the distributor, there is no separate sensor.

User Avatar

Here's the technical description of the p0340-344 diagnostic trouble codes: P0340 Camshaft Position Sensor Circuit Malfunction P0341 Camshaft Position Sensor Circuit Performance P0342 Camshaft Position Sensor Circuit Low Input P0343 Camshaft Position Sensor Circuit High Input P0344 Camshaft Position Sensor Circuit Intermittent Obviously, the camshaft position sensor (CPS) is the probable source of the problem. See "Related Questions" below for more about the CPS

User Avatar

Where is the camshaft position sensor on a 2005 Expedition?

User Avatar

The 1995 for Crown Victoria camshaft position sensor can be found on the back of the cylinder head. The camshaft position sensor will be labeled as such.

User Avatar

location of the camshaft sensor

User Avatar

The camshaft position sensor on a Mazda Miata is changed by disconnecting the wiring harness and unscrewing the sensor using a wrench. The threads can then be cleaned and a new sensor torqued into place.

User Avatar

Camshaft position sensor circuit malfunction.Camshaft position sensor circuit malfunction.

User Avatar

On top of the cam sensor synchronizer which is sticking out of the top of the timing cover on the front of the engine.

User Avatar

CMP-camshaft position sensor CKP-crankshaft position sensor

User Avatar

The Pontiac 2.2 liter engine camshaft position sensor can be found on the back of each cylinder head. The camshaft position sensor should be labeled as such.

User Avatar

There isn't a camshaft position sensor. If you are asking because of an error code you received, it is caused by a signal that mimics the same signal as a camshaft position sensor.

User Avatar

The camshaft position sensor is located on the end of the camshaft housing, on a 2002 Daewoo. The sensor should be labeled as such.

User Avatar

The Camshaft sensor is located in the distributor.

User Avatar

CMP : camshaft position sensorCKP : crankshaft postion sensor.CMP : camshaft position sensorCKP : crankshaft postion sensor.

User Avatar

Camshaft position actuator A bank 2 usually means change the camshaft position sensor

User Avatar

The 2006 Honda Accord camshaft position sensor can be found on the back of the right-hand cylinder head. The camshaft position sensor should be labeled as such.

User Avatar

i have been told my camshaft position sensor needs changing on my Renault scenic 2005 model a have brought one but don't know where it is to change it

User Avatar

were is the camshaft position sensor on 1999 Volvo s80 turbo

User Avatar

Where is the camshaft position sensor located on 1990 Lexus ls400?

User Avatar

if there is no camshaft position sensor then why am i getting codes for it and how do i eliminate those codes?

User Avatar

Yea, the crankshaft sensor is under the distributor and the camshaft sensor is inside the distributor, you cannot change it so you will have to replace the whole distributor.

User Avatar

change the camshaft position sensor, workind on mine.

User Avatar

The camshaft position sensor on a 4.6 liter engine is positioned on the side of the motor on the front of the cylinder head. A 4.6 liter engine has a camshaft position sensor on each cylinder head.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.