answersLogoWhite

0


Best Answer

2.0L Engine Fig. 1: Remove the three starter mounting bolts Fig. 2: Carefully lower the starter out of the vehicle # Disconnect the negative battery cable. # Remove air intake resonators. # Remove starter motor upper mounting bolts. # Raise and support the vehicle. # Remove the nuts on the starter terminals and remove the cables from the terminals. # Remove the two starter lower retaining bolts and remove the starter. To install: # Place the starter into position and tighten the 2 lower retaining bolts to 15-20 ft. lbs (20-27 Nm). # Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm). # Lower the vehicle. # Install and tighten the upper retaining bolt to 15-20 ft. lbs (20-27 Nm). # Install the air intake resonators. # Connect the negative battery cable. 2.5L Engine Fig. 3: Starter mounting - 2.5L engine # Disconnect the negative battery cable. # Remove the engine air cleaner assembly. # Remove the fuel feed and return lines from the support bracket located on the accelerator cable bracket, and remove the fuel line bracket. # On vehicles equipped with a automatic transaxle, remove the gear selector and the gear shift cable bracket from the transaxle. # Remove the air cleaner support bracket from the engine and transaxle mount. # Remove the nuts on the starter terminals and remove the cables from the terminals. # Remove the starter motor-to-transaxle case retaining bolt at the rear of the starter. # Remove the two starter retaining bolts and carefully lift the starter from the transaxle case while disengaging the alignment pins. To install: # Position the starter onto the alignment pins and onto the transaxle case. # Install the two starter retaining bolts and the rear retaining bolt and tighten them to 15-21 ft. lbs. (21-29 Nm). # Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm). # Install the air cleaner support bracket. # If removed, install the gear shift selector and bracket. # Install the fuel line bracket and install the fuel lines in the bracket. # Install the air cleaner assembly. # Connect the negative battery cable. Reference http://www.freeautomechanic.com

User Avatar

Wiki User

โˆ™ 2008-03-01 16:33:18
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you change a starter on a 2000 Mercury Cougar?
Write your answer...
Submit
Related questions

How do you change a fan switch on a 2000 Mercury Cougar?

How do i find the instructions for changing out the fan switch assembly in a 2001 Mercury Cougar?


Wrench light on 2000 Mercury Cougar?

You need an oil change.


How do you reset the anti theft system on a 2000 mercury cougar?

where is the anti theft located on a 2000 mercury cougar


How do I change the fuel pump relay on a 2000 Mercury cougar?

relays just plug in to the fusebox


Why does a 2000 Mercury Cougar only make a clicking noise when trying to start if the battery was checked and is ok?

Needs a new starter


Is there a transmission fluid dipstick on a manual 2000 mercury cougar?

On a 2000 Mercury Cougar : No , only the automatic transaxle ( transmission ) has a dipstick


Check a starter for a 2000 Mercury Grand Marquis?

how to replace starter on 2000 mercury grand marquis


Can You Turbocharge A 2000 Mercury Cougar?

Of Course


How many gallons does a 2000 Mercury Cougar gas tank hold?

For a 2000 Mercury Cougar : The tank holds ( 15.4 US. gallons )


2000 mercury cougar obd located?

The 2000 Mercury Cougar OBD 2 port is under driver side dash next to kick panel


Clutch fluid reservoir on a 2000 Mercury Cougar?

On a 2000 Mercury Cougar : The brake fluid reservoir is also the clutch fluid reservoir


Will 18 inch rims fit on 2000 mercury cougar?

sure! i have 19" alloy wheels on my 2000 cougar


Where is the obd-ii connection on a 2000 mercury cougar?

The 2000 Mercury Cougar OBD 2 port is under driver side dash next to kick panel


Where is the starter for a 2000 Mercury Sable?

The 2000 Mercury Sable starter can be found on the right hand side of the engine. The starter will be near the back of the engine.


How do you change fuel filter on a 2000 cougar?

what kind of tools do i need to change a fuel filter on a 2000 cougar


What type of oil does a 2000 Mercury cougar use?

According to the 2000 Mercury Cougar owners manual ( 5W-30 ) for the four cylinder and V6 engines


How many bolts in 2000 Mercury Sable starter?

The 2000 Mercury Sable starter will have three retaining bolts. There will be two cable retaining nuts on the front of the starter.


What is the blinking red light on the dashboard above the heater controls in the 2000 mercury cougar?

On a 2000 Mercury Cougar : That's your Anti-theft system status light


What is the location of coolant temperature switch on a 2000 Mercury Cougar?

it is right across from my thermostat and i have a 2000 mercury cougur it srews in and out.


How do you change the struts on a 2000 Mercury Cougar?

Check out autozone.com's repair guides online, under suspension, they have a good guide for doing it.


How many liters of oil for a 2000 mercury cougar 2.5 engine?

According to the 2000 Mercury Cougar Owner Guide : With engine oil filter change : The 2.5 liter V6 engine takes ( 5.5 liters of 5W-30 engine oil )


Where is the fusible link for the alternator charging system on a 1990 mercury cougar?

I can tell you that on a 2000 mercury cougar it is a fuse on the positive cable between the battery and the alternator


What is the tire size for 2000 Mercury Cougar?

my tire sizes for my cougar are P215/50R16 or go here so you can find your size http://www.dragtimes.com/Mercury-Cougar-Tires-m31-n237.html


How do you get to the fuel pump 2000 mercury cougar?

it is under the back seat


What is the lug pattern for a 2000 Mercury Cougar?

http://www.discountedwheelwarehouse.com/Mercury___Vehicle_Bolt_Pattern_Reference.cfm