answersLogoWhite

0


Best Answer

When replacing a water pump, it is necessary to drain the cooling system. Any components--belts, fan, fan shroud, shaft spacers, or viscous drive clutch--should be removed to make the pump accessible. Some pumps are attached to the cylinder block as shown below. Installing a water pump. Courtesy of Dana Corporation. Loosen and remove the bolts in a crisscross pattern from the center outward. Insert a rag into the block opening and scrape off any remains of the old gasket. WARNING When working on the coolant system (for example, replacing the water pump or thermostat), a certain amount of coolant will spill on the floor. The antifreeze in the coolant causes it to be very slippery. Always immediately wipe up any coolant that spills to reduce or eliminate the chance of injury. When replacing a water pump, always follow the procedures recommended by the manufacturer. Most often a coating of good waterproof sealer should be applied to a new gasket before it is placed into position on the water pump. Coat the other side of the gasket with sealer, and position the pump against the engine block until it is properly seated. Install the mounting bolts and tighten them evenly in a staggered sequence to the torque specifications with a torque wrench. Careless tightening could cause the pump housing to crack. Check the pump to make sure it rotates freely. The water pumps on many late-model OHC engines are driven by the engine's timing belt. When replacing the water pump on these engines, always replace the timing belt. Make sure all pulleys and gears are aligned according to specifications when installing the belt.

User Avatar

Wiki User

โˆ™ 2006-11-13 14:43:34
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change a water pump on a 1994 Chevrolet S10 4.3L?
Write your answer...
Submit
Related questions

How do you change the fuel pump on a 1994 Chevrolet Caprice Classic?

You have to remove the fuel tank to access the fuel pump.


How do you change the water pump on a 1994 Camaro?

take it to a mechanic.


How do you find and change the water pump in a 1986 Chevrolet Celebrity?

what type of engine do you have?? V6


Replace water pump on a 1994 Isuzu Rodeo?

replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo 6 cylinder


How do you change the fuel pump in a 1994 Chevrolet camaro Z28?

It's in the gas tank so the tank has to come down to get it out.


How do you change a water pump on a 1995 Chevrolet C1500 pickup truck?

Follow Link Below ..


How do you change a water pump 1987 Monte Carlo?

Remove the belt from your 1987 Chevrolet Monte Carlo water pump. Remove the water pump return hose. Remove the water pump retaining bolts. Reverse the process to install the new water pump.


Where is water pump on a 1987 Chevrolet celebrity?

The water pump is on the front of the engine.


How do you change a water pump on a 1998 Chevy k1500 4wd pickup?

Remove the water return line from your 1998 Chevrolet pickup truck water pump. Remove the water pump belt. Remove the water pump retaining bolts. Reverse the process to install the new water pump.


How do you change a water pump on a 1994 Geo tracker?

In order to change the water pump the first step is removing the grill and then the radiator fan assembly. Once this is done the water pump is accessible it will have four bolts that must be removed in order to take out the water pump.


Where is the fuel pump located on a 1994 Chevrolet Caprice?

in the tank itself


How do you change water pump on 1994 trooper?

Remove the serpentine belt. Drain the water from the radiator. Remove the radiator hose from the water pump. Remove the water pump retaining bolts. Reverse the process to install the new water pump.


I have replaced the fuel pump in my 1994 Chevrolet s10 blazer i am still having problems?

i have no electric to pump


1994 Acura water pump replaceing?

diagram of where the water pump is located on 1994 acura legend v6 diagram of where the water pump is located on 1994 acura legend v6


How do you change the water pump on a 1994 Chrysler concord?

The water pump on a 1994 Chrysler Concord is changed by removing the engine accessories, disconnecting the radiator hoses, and unbolting it from the engine block. The surface is then cleaned, a new gasket installed, and a replacement water pump mounted.


How do you replace water pump on Chevrolet V8 5.7 Liter 350?

Drain the water from your Chevrolet 5.7 liter engine cooling system. Remove the water pump return hose. Remove the water pump belt. Remove the water pump retaining bolts. Reverse the process to install the new water pump.


Do Chevrolet water pump bolts needs a sealant?

The Chevrolet water pump bolts do need a sealant. Thread tape can be used on the bolts in the place of a sealant.


How do you change a water pump on a 1994 Chevrolet Impala?

Go to your local parts store or book store and purchase a Haynes Manual. They have one that only covers your car. It is a great investment if you plan on doing your own repairs.


How do you replace the water pump on a 1994 Toyota Camry?

Answering "How do you replace the water pump on a 1994 Toyota Camry?"


How many bolts are in a Chevrolet water pump?

4


How do you replace the water pump on a 1994 Chevy Lumina?

Remove the belt from your 1994 Chevy Lumina water pump. Remove the water pump return hose. Remove the water pump retaining bolts. Reverse the process to install the new water pump.


How do you install a fuel pump on a 1994 Chevrolet Impala SS?

You will have to remove the gas tank and install a fuel pump module.


Do you have to change the timing belt on Dodge Voyager Plymouth 1994 when you change the water pump?

No, you do not have to replace the timing belt at the same time as the water pump. It is highly recommended because there is no additional labor involved since the timing belt must be removed to replace the water pump.


How do you change the water pump in a 1994 E320 Mercedes?

AnswerIf it your first time changing a water pump in a vehichle I would not recommend attempting this yourself as special tools are required to do the job properly.this is not my first time changeing a water pump


How do you replace the water pump in a 1995 Chevy k1500?

Remove the belt from your 1995 Chevrolet water pump. Remove the water pump hose. Remove the water pump retaining bolts. Reverse the process to install the new water pump.