answersLogoWhite

0


Best Answer

Disconnect your negative battery cable. Pull out the coil to distributer cap wire. unplug the wires going into the coil, remove the bolts holding the coil mounting bracket and slide coil out.

User Avatar

Wiki User

โˆ™ 2005-11-10 17:41:28
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you change an ignition coil on a 1991 F-350 58litre engine?
Write your answer...
Submit
Related questions

What is the ignition timing for a Mazda 323 1991 DOHC B5 engine?

ignition problem


What is the ignition timing for 1991 Toyota pickup?

wich engine do you have?


Where is the ignition module on a 1991 Oldsmobile regency?

The Ignition Control Module is on the top left hand side of the engine under the Ignition Coils.


Where is the dura spark ignition module located on a 1991 Ford probe?

The 1991 Ford Probe spark ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


1991 Honda Accord engine cuts out while driving?

Ignition switch


When did ECM take over from manually adjusting the distributor to change ignition timing.?

Right from the 1991 Explorer , the 4.0 L OHV engine was EDIS ( electronic distributorless ignition system ) using a coil pack instead of a distributor


How do you change a ignition switch on a 1991 cougar?

Ok so you have to go where the ignition switch is at on the 1991 cougar. Next, You have to take the old one out. Last, you have to put the new one in.


A engine diagram for a 1991 2.2 Honda Accord for the coolant hoses?

A Ignition coil diagram for 1991 2.2 Honda accord


How do you change the ignition key on a 1991 Toyota Previa?

Turn the key to acc. and push the plunger in located on the Ignition lock housing


How do you change the key cylinder of the ignition switch in a 1991 acura legend?

Remove the retaining ring at the top of your 1991 Acura Legend ignition switch. The ignition switch cylinder will slide out. Remove the wiring harness from the end of the ignition cylinder. Reverse the process to install your new ignition switch cylinder.


How do you change the ignition switch on a 1991 Pontiac grand am tilt steering automatic trans?

I don't know how to change the ignition switch but I have some advice. Don't screw with the ignition switch, buy the whole steering column. It will be cheaper and easier to change.


Where is the coil ignition located for 1991 beretta 3.1?

front of engine block right next to the starter.


How do you change the ignition cylinder on a 1991 Cadillac Eldorado?

Remove steering wheel and signal switch


How do you reset the change oil light on a 1991 Eldorado?

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds


How do you change the ignition in a 1991 Honda accord?

If you are having the same issues (starting problems-no spark) that I had in my 1991 accord, I found out that there appearantly was a recall on the distributor. Do not try to replace pieces and parts of the ignition system. (ie. coil, ignition control module, etc.) Replace the entire distributor. It will save you hours of frustration.


How do you change the oil pump on a 1991 Chevy Caprice?

its a wrap get an new engine


How to hot wire ignition of 1991 Mazda protege?

Can someone please tell me how to hot wire the ignition of a 1991 mazda protege?


What is the fuel pump pressure for a 1991 Pontiac firefly 3 cylinder?

engine off and ignition on: 23 to 31 psi engine at idle: 13 to 20 psi


Why is the service engine light on your 1991 S10 Chevy blazer?

time for an oil change


How do you change clock radio time 1991 osmobile calais?

With ignition on, radio off, hold in the "set" button. Turn the volume knob to change the hours, and the tuner knob to change the minutes.


Can you change the intake manifold on a 1995 4.3 vortex and use the engine in a 1991 throttle body truck?

No with much ease. The 95 engine is electronically controlled, and won't be compatible with a 1991 vehicle.


Where is the ignition control module on a 1994 ford explorer?

From 1991 to 1995 with the EEC-IV system there is an external ignition control module mounted on the radiator support in front of the battery. Remove the battery in order to change the module. 1996 and newer with the EEC-V system, the ignition control module is incorperated into the powertrain control module (PCM) that is visible from the engine compartment, in the firewall, on the passenger side.


What is the oil capacity on a 1991 camaro rs 3.1L engine?

4.5 quarts with a filter change.


How do you remove and replace the ignition switch on a 1991 Mercury Sable?

The 1991 Mercury Sable ignition switch is held in place with a retaining ring. Loosen the retaining ring. Pull the ignition switch out. Remove the wiring harness from the rear of the ignition switch. Reverse the process to install the new ignition switch.


How do you change ignition switch on Honda civic 1991?

your local library may have a free shop manual to peek at.. good luck Dave